User manual ALCATEL-LUCENT OMNISTACK 6124

[. . . ] A February 2002 OmniStack® 6124 Users Guide An Alcatel service agreement brings your company the assurance of 7x24 no-excuses technical support. You'll also receive regular software updates to maintain and maximize your Alcatel product's features and functionality and on-site hardware replacement through our global network of highly qualified service delivery partners. Additionally, with 24-hour-a-day access to Alcatel's Service and Support web page, you'll be able to view and update any case (open or closed) that you have reported to Alcatel's technical support, open a new case or access helpful release notes, technical bulletins, and manuals. For more information on Alcatel's Service Programs, see our web page at www. ind. alcatel. com, call us at 1-800-995-2696, or email us at support@ind. alcatel. com. This Manual documents OmniStack 6124 hardware and software. [. . . ] Displays the address table sorted on VID and then Multicast IP. Scrolls through the entries in the address table. 2-54 Monitoring the Switch Configuring Static Unicast Addresses Use the Static Unicast Address Table Configuration screen to manually configure host MAC addresses in the unicast table. You can use this screen to associate a MAC address with a specific VLAN ID and switch port as shown below. Alcatel OmniStack 6124 < Static Unicast Address Table Configuration > VID MAC Address Unit Port Status -----------------------------------------------------------1 00-00-00-E8-43-12 1 1 Permanent Sorted by : VID + MAC VID : 1 MAC : 00-00-00-00-00-00 [Show] [More] VID : 1 MAC : 00-00-00-00-00-00 Port : 1 Status : Permanent [Set] <OK> Use <TAB> or arrow keys to move, <Enter> to select. Menu VID MAC Address Unit Port Status Description The VLAN group this port is assigned to. The MAC address of a host device attached to this switch. The switch unit the host device is attached to. The port the host device is attached to. The status for an entry can be set to: Permanent This entry is currently in use and will remain so after the next reset of the switch. DeleteOnReset This entry is currently in use and will remain so until the next reset. Invalid Removes the corresponding entry. DeleteOnTimeOut This entry is currently in use and will remain so until it is aged out. (Refer to "Aging Time" on page 2-53. ) Other This entry is currently in use but the conditions under which it will remain so differ from the preceding values. Selects the primary sort key for displaying table entries. Note that only VID+MAC is implemented in the current firmware release. Displays the static address table sorted on VID as the primary key and MAC address as secondary key. Scrolls through entries in the static address table. Adds the specified entry to the static address table, such as shown in the following example: VID Unit Status :1 MAC : 00-00-00-e8-34-22 :1 Port: 1 : Permanent Sorted by [Show] [More] [Set] 2-55 Using the System Configuration Program Resetting the System Use the Restart command under the Main Menu to reset the management agent. The reset screen includes options as shown in the following figure and table. Alcatel OmniStack 6124 < Reset System Menu > Restart Option : POST Reload Factory Defaults Keep IP Setting Keep User Authentication [Restart] : : : : YES NO NO NO <Apply> <Ok> <Cancel> Use <TAB> or arrow keys to move, <Space> to scroll options. Menu POST Reload Factory Defaults Keep IP Setting Keep User Authentication [Restart] Description Runs the Power-On Self-Test Reloads the factory defaults Retains the settings defined in the IP Configuration menu. Retains the user names and passwords defined in the Console Login Configuration menu. Restarts the switch. Logging Off the System Use the Exit command under the Main Menu to exit the configuration program and terminate communications with the switch for the current session. 2-56 Chapter 3: Web-Based Management Web-Based Configuration and Monitoring As well as the menu-driven system configuration program, the agent module provides an embedded HTTP Web agent. This agent can be accessed by any computer on the network using a standard Web browser (Internet Explorer 4. 0 or above, or Netscape Navigator 4. 0 or above). Using the Web browser management interface you can configure a switch and view statistics to monitor network activity. The Web interface also provides access to a range of SNMP management functions with access to the switch's MIB and RMON database. [. . . ] Change your baud rate to 115200 bps, and press Enter to enable download mode. From the terminal emulation program, select the file you want to download, set the protocol to XModem, and then initialize downloading. Notes: 1. If you use Windows HyperTerminal, disconnect enable the new baud rate. The download file should be an OmniStack® 6124 binary file from Alcatel; otherwise the agent will not accept it. [. . . ]