User manual ALCATEL-LUCENT SPEDDTOUCH PRO WITH FIREWALL

[. . . ] SPEED TOUCH PRO WITH FIREWALL User's Guide 3EC 36231 ABAA TCZZA Ed. 01 Status Change Note Released BD F aa 36170 Short Title CD-UG STPro 3. 4. 2 All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel. 2 / 288 3EC 36231 ABAA TCZZA Ed. 01 Contents Contents 1 Speed Touch Quick Guide . [. . . ] 01 147 / 288 13 Networking - ATM The 'Phonebook' table The following figure shows an example of the 'Phonebook' table of the 'Phonebook' page: 'Phonebook' table components Field Name Address Description Indicates the name, or alias of the phonebook entry. Indicates the VPI and VCI value of the ATM VC terminated on the DSL port for the phonebook entry. The allowed VCI range: from 32 up to 511. Note: In case your single Ethernet port STPro is equipped with an ATMF 25. 6 port, VPI values 0 to 7 are cross connected between the DSL port and the ATMF 25. 6 port. 148 / 288 3EC 36231 ABAA TCZZA Ed. 01 13 Networking - ATM Field Type Description Represents the connection service supported on the ATM VC. It can take the following values: Value ETHoA Packet Service Transparent Bridging Routed Ethernet (MER) See chapter 7 for more information. Bridged PPPoE See chapter 8 for more information. Routed PPPoE See chapter 9 for more information. PPPoA RFC2364 Relayed PPPoA See chapter 10 for more information. Routed PPPoA See chapter 11 for more information. IPoA RFC1483/Rt any CIP & IP Routing See chapter 12 for more information. Any kind of packet service is allowed. RFC1483/Br See chapter 6 for more information. Auto PVC Indicates whether the entry is listed in the 'AutoPVC' list (yes) or not (no). See subsection 13. 3. 3 for more information. Available Indicates the availability of the VC phonebook entry. An entry is available if it is not configured in any STPro packet service page, or not in temporary use by a packet service. Phonebook defaults The phonebook entries configured by default are listed in appendix C. 3EC 36231 ABAA TCZZA Ed. 01 149 / 288 13 Networking - ATM The 'ATMF ADSL Xconnects' table The following figure shows the 'ATMF ADSL Xconnects' table: This table, which is only present in case of a dual port STPro, indicates all cross connections between the DSL line and the ATMF25. 6 port. The 'AutoPVC' table The following figure shows an example of the 'AutoPVC' table: Any PVC, identified by its VPI/VCI and communicated via AutoPVC is added to the 'AutoPVC' table. If AutoPVC is not supported at the remote side, i. e. the Digital Subscriber Line Access Multiplexer (DSLAM), the 'AutoPVC' table stays empty. See subsection 13. 3. 3 for more information. 150 / 288 3EC 36231 ABAA TCZZA Ed. 01 13 Networking - ATM 13. 3. 2 Using the Phonebook Introduction The main function of the STPro phonebook is to present an instant overview of all possible entries and their status. Another important function is that it helps you to navigate through the various STPro VC connection possibilities. In this subsection " " " Restrictions for Adding Phonebook Entries Adding Entries Deleting Entries. Restrictions for adding phonebook entries Although you are free to give any name to a phonebook entry, a few restrictions apply: " You may not provide an entry with a name which already is supplied in the 'Phonebook' table. Phonebook entries, which are intended to be used for the Relayed PPPoA packet service may not start with a capital 'P' or a capital 'T'. [. . . ] This equipment generates, uses and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment ON and OFF, the user is encouraged to try correct the interference by one or more of the following measures: " Reorient or relocate the receiving antenna " Increase the separation between the equipment and receiver " Connect the equipment into an outlet on a circuit different from that to which the receiver is connected " Consult the dealer or an experienced radio/television technician for help. [. . . ]