User manual ALCATEL-LUCENT SPEEDTOUCH 500 1

[. . . ] SpeedTouchTM 500Series Multi-User ADSL Gateways CLI Reference Guide Release R4. 2 500 SERIES SpeedTouchTM 500Series CLI Reference Guide Release R4. 2 Status Change Note Short Title Copyright Released PeckelbeenS CLI ST500Series R4. 2 © 2003 THOMSON. Passing on, and copying of this document, use and communication of its contents is not permitted without written authorization from THOMSON. The content of this document is furnished for informational use only, may be subject to change without notice, and should not be construed as a commitment by THOMSON. THOMSON assumes no responsibility or liability for any errors or inaccuracies that may appear in this document. Content About this Document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Mss clamping assures that the size of a TCP packet never exceeds the available mtu of the outgoing interface. It is recommended not to disable this parameter. OPTIONAL 204 IP Commands EXAMPLE: =>ip config Forwarding on Firewalling off Sendredirects off Sourcerouting on NetBroadcasts off Default TTL 128 Fraglimit 32 fragments Fragcount currently 0 fragments Defragment mode : always Address checks : static Mss clamping : on =>ip config firewalling=on ttl=64 fraglimit=64 defragmode=nat =>ip config Forwarding on Firewalling on Sendredirects off Sourcerouting on NetBroadcasts off Default TTL 64 Fraglimit 64 fragments Fragcount currently 0 fragments Defragment mode : nat Address checks : static Mss clamping : on => RELATED COMMANDS: ip ifconfig Configure interface parameters. 205 IP Commands ip flush Flush complete IP configuration. Note Note SYNTAX: ip flush As an ip flush causes all local IP connectivity to be deleted, do not execute this command during an IP based local connection, e. g. a Telnet CLI session, or web based CLI access. The flush command does not impact previously saved configurations. EXAMPLE: =>ip aplist 3 cip1 Type:ATM inet addr:172. 16. 0. 5 Bcast:172. 16. 0. 255 Mask:255. 255. 255. 0 UP RUNNING pat MTU:9180 ReasmMAX:65535 Group:0 IPRX bytes:0 unicastpkts:0 brcastpkts:0 IPTX bytes:0 unicastpkts:0 brcastpkts:0 droppkts:0 HWRX bytes:0 unicastpkts:0 brcastpkts:0 HWTX bytes:0 unicastpkts:0 brcastpkts:0 droppkts:0 2 eth0 Type:EthernetHWaddr 00:80:9f:24:ab:cf BRHWaddr ff:ff:ff:ff:ff:ff inet addr: 10. 0. 0. 2 Bcast: 10. 0. 0. 255 Mask: 255. 255. 255. 0 UP RUNNING pat MTU:1500 ReasmMAX:65535 Group:2 IPRX bytes:0 unicastpkts:0 brcastpkts:0 IPTX bytes:0 unicastpkts:0 brcastpkts:0 droppkts:0 HWRX bytes:0 unicastpkts:0 brcastpkts:0 HWTX bytes:0 unicastpkts:0 brcastpkts:0 droppkts:0 0 loop Type:0 inet addr:127. 0. 0. 1 Bcast:127. 255. 255. 255 Mask:255. 0. 0. 0 UP RUNNING MTU:1500 ReasmMAX:65535 Group:1 IPRX bytes:116 unicastpkts:0 brcastpkts:2 IPTX bytes:0 unicastpkts:0 brcastpkts:0 droppkts:0 HWRX bytes:0 unicastpkts:0 brcastpkts:0 HWTX bytes:0 unicastpkts:0 brcastpkts:0 droppkts:0 =>ip flush =>ip aplist 3 cip1 Type:ATM inet addr:172. 16. 0. 5 Bcast:172. 16. 0. 255 Mask:255. 255. 255. 0 UP RUNNING pat MTU:9180 ReasmMAX:65535 Group:0 IPRX bytes:0 unicastpkts:0 brcastpkts:0 IPTX bytes:0 unicastpkts:0 brcastpkts:0 droppkts:0 HWRX bytes:0 unicastpkts:0 brcastpkts:0 HWTX bytes:0 unicastpkts:0 brcastpkts:0 droppkts:0 0 loop Type:0 inet addr: 127. 0. 0. 1 Bcast:127. 255. 255. 255 Mask:255. 0. 0. 0 UP RUNNING MTU:1500 ReasmMAX:65535 Group:1 IPRX bytes:116 unicastpkts:0 brcastpkts:2 IPTX bytes:0 unicastpkts:0 brcastpkts:0 droppkts:0 HWRX bytes:0 unicastpkts:0 brcastpkts:0 HWTX bytes:0 unicastpkts:0 brcastpkts:0 droppkts:0 => 206 IP Commands ip ifconfig Configure IP interface parameters. SYNTAX: ip ifconfig intf = <interface name> [mtu = <number{68-20000}>] [status = <{down|up}>] [hwaddr = <hardware-address>] [group = <{wan|local|lan}>] [linksensing = <{off|on}>] The IP interface name. Represents the maximum transmission unit, i. e. the maximum packet size (including IP header) to use on this interface. The default value depends on the connection and packet service for which the interface was created. The administrative status of the interface. Choose between: · · hwaddr group linksensing EXAMPLE: =>ip iflist Interface GRP MTU RX TX 0 loop 1 1500 116 0 1 eth0 2 3000 21045795 1019664 2 NewETHoA 0 1500 0 0 5 cip0 0 9180 0 0 =>ip ifconfig intf=eth0 mtu=1500 =>ip iflist Interface GRP MTU RX TX 0 loop 1 1500 116 0 1 eth0 2 1500 21054963 1025417 2 NewETHoA 0 1500 0 0 5 cip0 0 9180 0 0 => intf mtu REQUIRED OPTIONAL status OPTIONAL down up OPTIONAL OPTIONAL OPTIONAL The hardware address (e. g. the Ethernet MAC address) of this interface. The group this interface belongs to (e. g. The IP interface's awareness of link state transitions. TX-DROP 0 0 0 0 STATUS UP UP UP UP HWADDR 00:80:9f:24:ab:cf 00:80:9f:24:ab:cf TX-DROP 0 0 0 0 STATUS UP UP UP UP HWADDR 00:80:9f:24:ab:cf 00:80:9f:24:ab:cf RELATED COMMANDS: ip config Show/set global IP stack configuration options. 207 IP Commands ip iflist Show all current interfaces. SYNTAX: ip iflist EXAMPLE: =>ip iflist Interface GRP 0 loop 1 1 eth0 2 2 NewETHoA 0 5 cip0 0 => MTU RX 1500 116 3000 21045795 1500 0 9180 0 TX 0 1019664 0 0 TX-DROP 0 0 0 0 STATUS UP UP UP UP HWADDR 00:80:9f:24:ab:cf 00:80:9f:24:ab:cf RELATED COMMANDS: ip ifconfig Configure interface parameters. 208 IP Commands ip ifwait Wait for a status change of an IP interface. SYNTAX: ip ifwait intf = <interface name> [timeout = <number{1-600000}>] [adminstatus = <{down|up}>] [operstatus = <{down|up}>] [linkstatus = <{down|up}>] The IP interface name. The administrative state of the interface. Choose between: · · operstatus down up OPTIONAL REQUIRED OPTIONAL OPTIONAL intf timeout adminstatus The operational state of the interface. Choose between: · · down up linkstatus The link state of the interface. Choose between: · · down up OPTIONAL 209 IP Commands ip ping Send ICMP ECHO_REQUEST packets. SYNTAX: ip ping addr = <ip-address> [count = <number{1-1000000}>] [size = <number{1-20000}>] [interval = <number{100-1000000}>] [listen = <{off|on}>] The destination IP address. Represents the size of the ping packet(s). [. . . ] Shows the status of the wireless interface. 396 E-SIT-CTC-20030410-0050 Ed. 03 Wireless Commands wireless scan Scans for other APs in the area. An overview of all the radio channels and their respective ratings is shown. SYNTAX: wireless scan EXAMPLE: =>wireless scan Channel rating 1 : Good 2 : Good 3 : Good 4 : Good 5 : Good 6 : Recommended 7 : Good 8 : Good 9 : Good 10 : Good 11 : Good Recommended channel : 6 => RELATED COMMANDS: wireless ifconfig wireless status Configures and shows the wireless interface parameters. [. . . ]