User manual ALCATEL-LUCENT SPEEDTOUCH 516 1 536 1 546 1 510V5 1 530V5

[. . . ] SpeedTouchTM 516/536/546/510v5/530v5 Multi-User ADSL Gateways Setup and User's Guide Release R5. 2. 7 SpeedTouchTM 516/536/546 510v5/530v5 Setup and User's Guide R5. 2. 7 Copyright Copyright ©1999-2004 THOMSON. Passing on, and copying of this document, use and communication of its contents is not permitted without written authorization from THOMSON. The content of this document is furnished for informational use only, may be subject to change without notice, and should not be construed as a commitment by THOMSON. THOMSON assumes no responsibility or liability for any errors or inaccuracies that may appear in this document. [. . . ] Make sure Built-in Ethernet is selected in the Show list and click the PPPoE tab: 4 Enter the Account Name and Password provided by your Service Provider. Select Save password in case you want the computer to remember the password for this account name. Optionally you can enter a name for this connection in the Service Provider field. All other fields may stay empty 5 Starting a broadband Internet session Click Apply Now. Proceed as follows: 1 Click the Internet Connect dockling. If the Internet Connect dockling is not available, go to the Applications folder on the system startup disk and double-click Internet Connect. 2 The following window appears: Make sure Built-in Ethernet is selected in the Configuration list. 3 4 If needed, enter user name and password for your user account at the Service Provider. Click Connect. As soon as the connection is established you can open your web browser and surf the Internet. E-DOC-CTC-20040907-0001 v1. 0 39 Chapter 2 SpeedTouchTM Internet Connectivity Terminating a broadband Internet session Proceed as follows: 1 Click the Internet Connect dockling. If the Internet Connect dockling is not available, go to the Applications folder on the system startup disk and double-click Internet Connect. 2 The following window appears: Make sure Built-in Ethernet is selected in the Configuration list 3 Click Disconnect. The connection is released. As a result no Internet connectivity exists anymore. 40 E-DOC-CTC-20040907-0001 v1. 0 Chapter 3 SpeedTouchTM Web Interface 3 SpeedTouchTM Web Interface Introduction The SpeedTouchTM comes with integrated configuration web pages. It allows you to configure your SpeedTouchTM simply by using a web browser from any local computer connected to the SpeedTouchTM. In most cases the SpeedTouchTM is correctly configured for your internet connectivity via the appropriate configuration profile/file and no further configuration on the web interface is needed. Only for using and/or configuring the advanced SpeedTouchTM features, access to the web pages is required for specific configuration. This chapter aims to give a brief overview of the SpeedTouchTM web pages and their respective functionality. Preconditions Before you can access the SpeedTouchTM web pages, make sure that: The SpeedTouchTM and your computer share the same IP subnet (10. 0. 0. 0/24). By default the SpeedTouchTM has a local IP address 10. 0. 0. 138. To be able to access the web pages, your computer needs to be configured for an IP address in the same subnet, e. g. 10. 0. 0. 1 Your web browser is not using a proxy server and the SpeedTouchTM IP address is not submitted to a proxy server. To configure your computer with an IP address, please consult the Operating System's Help. For more information on how to disable your web browser's proxying, please consult the web browser's Help. Browsing to the SpeedTouchTM web pages To access the SpeedTouchTM web pages: 1 2 Start the web browser on your computer. Browse to the SpeedTouchTM at its IP address at 10. 0. 0. 138. 10. 0. 0. 138 is the SpeedTouchTM default IP address in the very most cases. If not, please contact your Internet Service Provider (ISP) for more information. 3 If a system password has been set, an authentication window will be displayed. You must enter the user name and system password before access will be granted. E-DOC-CTC-20040907-0001 v1. 0 41 Chapter 3 SpeedTouchTM Web Interface Access to the SpeedTouchTM web interface via UPnPTM ! If your computer runs Windows XP Service Pack 2 (SP2) and you are using the Windows Firewall, make sure the Windows Firewall allows incoming network connections for the UPnP service (see " Windows firewall configuration" on page 76). Click (Settings >) Control Panel on the Start menu to open the Control Panel. [. . . ] Under Network Tasks, click Change Windows Firewall settings. 3 4 5 The Windows Firewall window appears. Select the UPnP Framework check box: 6 Click OK. 76 E-DOC-CTC-20040907-0001 v1. 0 Chapter 5 Support Adding Internet Gateway Device Discovery and Control Your MS Windows XP system is able to discover and control Internet Gateway Devices (IGD), like the SpeedTouchTM on your local network. Therefore it is recommended to add the IGD Discovery and Control client to your system. Proceed as follows: 1 2 3 4 On the Start menu, click Control Panel. [. . . ]