User manual ALCATEL-LUCENT SPEEDTOUCH 546

[. . . ] SpeedTouchTM546 Residential ADSL Gateway User's Guide Release R5. 3. 1 SpeedTouchTM 546 User's Guide R5. 3. 1 Copyright Copyright ©1999-2005 THOMSON. Passing on, and copying of this document, use and communication of its contents is not permitted without written authorization from THOMSON. The content of this document is furnished for informational use only, may be subject to change without notice, and should not be construed as a commitment by THOMSON. THOMSON assumes no responsibility or liability for any errors or inaccuracies that may appear in this document. [. . . ] Select the configuration file you want to restore and click Open. The SpeedTouchTM loads your configuration and restarts. At the end of the procedure, the SpeedTouchTM returns to the Home page. 44 E-DOC-CTC-20050429-0100 v1. 0 Chapter 4 SpeedTouchTM Web Interface 4. 3. 6 Reset to Factory Defaults Introduction This page allows you to reset the SpeedTouchTM to return to the initial configuration of your SpeedTouchTM. All your changes will be deleted. Accessing the Reset to Factory Defaults page Proceed as follows: 1 2 On the left menu, click SpeedTouch. list, click Return to Factory Default Settings. Resetting the SpeedTouchTM to factory defaults If you want to reset your SpeedTouchTM to factory defaults, click Yes, reset my SpeedTouch. ! If you reset your SpeedTouchTM to factory default settings, all active connections will be disconnected. E-DOC-CTC-20050429-0100 v1. 0 45 Chapter 4 SpeedTouchTM Web Interface 4. 3. 7 Event Logs Event Logging The Event Logs page summarizes the latest events recorded on your SpeedTouchTM. Recorded Events table The Recorded Events table gives you an overview of the latest event logs that have been recorded since power on. The first column of the table indicates the importance of the event log Indicator Description Informational Warning Error The Category list allows you to filter the events shown in the Recorded Events table. For example, by clicking Security you can view all security related events, for example generated by the SpeedTouchTM firewall. 46 E-DOC-CTC-20050429-0100 v1. 0 Chapter 4 SpeedTouchTM Web Interface 4. 3. 8 Update Updating the SpeedTouchTM system software The Update page allows you to: View System Information. View information on the current System Firmware. Update your SpeedTouchTM from a remote server. Use this option if you want to have yourSpeedTouchTM check on the internet for new firmware and update if it found one. Use this option if you want to install on your SpeedTouchTM that is located on the PC. E-DOC-CTC-20050429-0100 v1. 0 47 Chapter 4 SpeedTouchTM Web Interface 4. 4 Broadband Connection The Broadband Connection menu The Broadband Connection menu consists of following menu items: DSL Connection Internet Services The Broadband Connection page The Broadband Connection page gives you a short status overview of the connections configured on the SpeedTouchTM. Click View more to see more information on the selected broadband connection. If you configured a dial-up connection, you are able to establish/terminate the connection by clicking Connect/Disconnect. 48 E-DOC-CTC-20050429-0100 v1. 0 Chapter 4 SpeedTouchTM Web Interface 4. 4. 1 Connectivity Check Introduction This page enables you to perform a connectivity check on an Internet service of your SpeedTouchTM. Accessing the Connectivity Check page Proceed as follows: 1 2 On the left menu, click Broadband Connection. list, click Check connectivity to the Internet. Checking you Internet Connectivity Proceed as follows: 1 2 3 In the Internet Service to Check list, click the Internet service that you want to check. The SpeedTouchTM lists the test results in the Test Results list. Analysing the test results If the test is successful, you will get a list of green check marks. Otherwise a red cross will indicate which tests have failed. E-DOC-CTC-20050429-0100 v1. 0 49 Chapter 4 SpeedTouchTM Web Interface 4. 4. 2 DSL Connection Overview Details Click Overview to view brief information on your DSL connection. Click Details to view a more detailed information on your DSL connection. 50 E-DOC-CTC-20050429-0100 v1. 0 Chapter 4 SpeedTouchTM Web Interface 4. 4. 3 Internet Services Internet Services information The Internet Services page displays information on your Internet Connection(s). If you configured a dial-up connection you are able to establish/terminate the connection by clicking Connect/Disconnect. To view more detailed information on a specific connection, click the View more. . . link of the corresponding connection. E-DOC-CTC-20050429-0100 v1. 0 51 Chapter 4 SpeedTouchTM Web Interface 4. 4. 4 Internet Service Settings Accessing the Internet Service Settings page Proceed as follows: 1 2 On the Broadband Connection menu click Internet Services. Click the View more link of the internet service you want to view. Overview The Overview page gives you basic information on the selected Internet Service. If you configured a connection you are able to establish/terminate the connection by clicking Connect/Disconnect. Details The Details page gives you more detailed information on the selected Internet Service. If you configured a dial-up connection you are able to establish/terminate the connection by clicking Connect/Disconnect. 52 E-DOC-CTC-20050429-0100 v1. 0 Chapter 4 SpeedTouchTM Web Interface 4. 5 Toolbox The Toolbox menu The Toolbox menu consists of following menu items: Remote Assistance: Allows you to make your SpeedTouchTM accessible for remote support. Game & Application Sharing: Allows you to share services and games that you run in your private network towards the internet. Parental Control: Allows you to block/allow access to specific web sites. [. . . ] Your computer doesn't support UPnPTM if you run an operating system other than MS Windows XP and MS Windows Millennium. Make sure that UPnPTM is not disabled in the SpeedTouchTM web page; see "4. 5. 2 Game & Application Sharing" on page 55. Adding UPnPTM If you are running Microsoft Windows XP, it is recommended to add the UPnPTM component to your system. Proceed as follows: 1 2 3 4 On the Start menu, click (Settings >) Control Panel. In the Add or Remove Programs window appears, click Add/Remove Windows Components. [. . . ]