User manual ALCATEL 29446 CE

[. . . ] Remark: If no number has been preset, 2 beep tones are emitted indicating the memory is empty. Adjust Ringer Volume You can select the ringer volume in standby mode or in phone setting mode or in ringing mode by pressing key and key during ringing phase. There are 6 levels (level 1 to 5 and off) Package contents: The package contains the following items: 1. 1 Alcatel 29446 CE with detachable belt clip 2. [. . . ] 14) Risk of explosion if battery is replaced by an incorrect type. INSTALLING YOUR PHONE 2. 1 Connecting the base charger !Warning: the ringer volume can be set to off, then, there is no ring alert from Alcatel 29446 CE during ringing 4. 5. Adjust Handsfree Volume There are 5 levels (VOLUME 1 to VOLUME 5) to choose from for each of headset and handsfree volume. During a call, press key or key to select volume 1-5. When you end the call, the setting will remain at the last selected level. Barge in a call / Call transfer Function is enabled for the limited bundle package (29446 CE + Versatis XL350, 29446 CE + Versatis XL350 Voice) only. When your telephone (Versatis XL 350 or Versatis XL350 voice) is in conversation you can join the call by pressing key of the 29446 CE. Then, when you end the call using the XL 350 or XL 350 voice handset during “barge in call” mode, it will transfer the call to the 29446 CE automatically. End a Call During a call connection, press either key OR put the Alcatel 29446 CE on the charger to end the call. . 4. 8. Intercom You can use another registered handset on the same base station. key again to disconnect Alcatel 29446 CE from the communication mode after you TABLE 1: PROGRAMMING SETTING Menu name Ringer volume control Ringtones on handset Quick dial Quick dial Quick dial Default settings Registration to be described in Section 4. 1 Pin Code Number Action Ring volume control Choose ringer melody Program M1 Program M2 Program M3 Secuencia en el teclado alfanumérico press " 05" + " "value" +"#" (complete by hearing a confirmation tone); value = 0 to 5 Wait the end of the melody for selecting another volume. press " 04" + " "value" +"#" (complete by hearing a confirmation tone); value = 1 to 5 Wait the end of the melody for selecting another volume. press " 01" + "number(20 digits in length)" + "#" (complete by hearing a confirmation tone ) press " 02" + "number(20 digits in length)" + "#" (complete by hearing a confirmation tone ) press " 03" + "number(20 digits in length)" + "#" (complete by hearing a confirmation tone ) SAFETY In the event of an electrical hazard, the mains adapter acts as 230V power isolating device. It should therefore, as a precaution, be installed close to the appliance and be easily accessible. To disconnect the device from the primary power source, the mains adapter must be removed from the 230V AC / 50 Hz socket. If the mains adapter fails, it must be replaced by an identical model. If not connected to the mains power or if there is a mains power failure, telephones that use cordless handsets will not work. You will then be unable to make or receive calls in the event of an emergency. This is why we recommend that you also keep a conventional telephone – one that doesn’t require a power supply – as a backup. Do not use your telephone to notify a gas leak when standing in the vicinity of the leak. It is recommended that you avoid using this device during electrical storms. [. . . ] Keen to preserve the environment, ATLINKS has equipped this appliance with a switching power supply, offering better energy efficiency. The advantages include not only very low electricity consumption, but also a more compact format than the conventional power supply units used by the previous range. The used batteries from your telephone (if it has batteries) must be disposed of in compliance with current environmental protection regulations. Return your batteries to your reseller or dispose of them at an approved recycling centre. TABLE 3: TONE INDICATION Tone Type Key Tone Confirmation Tone Error Tone Low Battery Tone Out Of Range Tone On Cradle Tone Behavior One Short Beep One Short Beep Two Consequence Short Beep Two Consequence Short Beep Two Consequence Short Beep One Short Beep Description Alert when key press Alert in programming mode when press # to confirm any settings or, when press # to save editing Alert In programming mode when invalid value is entered (e. g. [. . . ]