User manual ALINCO DJ-F4E

[. . . ] Reproduction in any manner whatsoever without the written permission of Dell Inc. Trademarks used in this text: Dell, the ALINCO logo, Inspiron, Dell Precision, Dimension, OptiPlex, Latitude, PowerEdge, PowerVault, PowerApp, PowerConnect, and Dell OpenManage are trademarks of Dell Inc. ; Intel, Pentium, and Celeron are registered trademarks of Intel Corporation; Microsoft, Windows, and Outlook are registered trademarks of Microsoft Corporation. Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. disclaims any proprietary interest in trademarks and trade names other than its own. Model DMC August 2005 P/N WD492 Rev. [. . . ] If two or more restore points are available, click the restore point that you prefer. The Restoration Complete screen appears after System Restore finishes collecting data and then the computer restarts. 6 After the computer restarts, click OK. To change the restore point, you can either repeat the steps using a different restore point, or you can undo the restoration. 42 Advanced Troubleshooting Undoing the Last System Restore NOTICE: Before you undo the last system restore, save and close all open files and exit any open programs. Do not alter, open, or delete any files or programs until the system restoration is complete. 1 Click the Start button, point to All Programs Accessories System Tools, and then click System Restore. 2 Click Undo my last restoration and click Next. The System Restore screen appears and the computer restarts. 4 After the computer restarts, click OK. Enabling System Restore If you reinstall Windows XP with less than 200 MB of free hard-disk space available, System Restore is automatically disabled. To see if System Restore is enabled: 1 Click the Start button and click Control Panel. 5 Ensure that Turn off System Restore is unchecked. Resolving Software and Hardware Incompatibilities If a device is either not detected during the operating system setup or is detected but incorrectly configured, you can use the Hardware Troubleshooter to resolve the incompatibility. 3 Disconnect your computer and all attached devices from their electrical outlets, and then press the power button to ground the system board. CAUTION: To guard against electrical shock, always unplug your computer from the electrical outlet before opening the cover. 4 Open the computer cover (see page 50). NOTICE: Before touching anything inside your computer, ground yourself by touching an unpainted metal surface, such as the metal at the back of the computer. While you work, periodically touch an unpainted metal surface to dissipate any static electricity that could harm internal components. 46 Removing and Installing Parts Front and Back View of the Computer Front View 1 10 2 9 3 8 7 4 6 1 2 3 4 5 6 CD or DVD driveactivity light CD or DVD drive eject button 5 The drive activity light is on when the computer reads data from the CD or DVD drive. Press to eject a disc from the CD or DVD drive. floppy-drive eject button Press to eject a floppy disk from the floppy drive. (On computers with an optional floppy drive. ) hard-drive activity light headphone connector USB 2. 0 connectors (2) The light is on when the computer reads data from or writes data to the hard drive. The light might also be on when a device such as your CD player is operating. Use the headphone connector to attach headphones and most kinds of speakers. Use the front USB connectors for devices that you connect occasionally, such as joysticks or cameras, or for bootable USB devices (see "System Setup" on page 80 for more information on booting to a USB device). It is recommended that you use the back USB connectors for devices that typically remain connected, such as printers and keyboards. 7 power button Press to turn on the computer. NOTICE: To avoid losing data, do not use the power button to turn off the computer. [. . . ] This device must accept any interference received, including interference that may cause undesired operation. Class A This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the manufacturer's instruction manual, may cause harmful interference with radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case you will be required to correct the interference at your own expense. [. . . ]