User manual ALPINE CDA-7969R

[. . . ] R CDA-7969R FM/MW/LW/RDS CD Player · OWNER'S MANUAL Please read before using this equipment. · BEDIENUNGSANLEITUNG Lesen Sie diese Bedienungsanleitung bitte vor Gebrauch des Gerätes. · MODE D'EMPLOI Veuillez lire avant d'utiliser cet appareil. · MANUAL DE OPERACIÓN Léalo antes de utilizar este equipo. [. . . ] When the automatic memory has been completed, the tuner goes to the station stored in the preset location No. 1. NOTE If no stations are stored, the tuner will return to the original station you were listening to before the auto memory procedure began. 5 Press the F button to activate the normal mode. The FUNC indicator will turn off. NOTES · If no stations are stored, the display shows "NO MEMORY. " · When the radio band is changed, the stations stored in memory using this function will be erased. · Operate the unit while the FUNC indicator is illuminated. If no buttons are pressed within 5 seconds, the FUNC indicator will turn off. 13-EN RDS Operation INTLZ TUNE DN g f UP F F1 F2 F3 Setting RDS Reception Mode and Receiving RDS Stations The RDS (Radio Data System) is a radio information system using the 57 kHz subcarrier of regular FM broadcast. The RDS allows you to receive a variety of information such as traffic information, station names, and to automatically re-tune to a stronger transmitter that is broadcasting the same programme. Tips The RDS digital data includes the followings: PI Programme Identification PS Programme Service Name AF List of Alternative Frequecncies TP Traffic Programme TA Traffic Announcement PTY Programme Type EON Enhanced Other Networks R. TEXT Radio Text Information Recalling Preset RDS Stations 1 2 3 4 1 2 3 Press the F button so that the FUNC indicator will illuminate. Press the F1 (AF) button to activate the RDS mode. The display shows "AF" when the RDS mode is activated. Press the F button to activate the normal mode. Make sure that the FUNC indicator light goes out, then press the F1 through F6 buttons in which your desired RDS station is preset. If the preset station's signal is weak, the unit automatically searches and tunes to a stronger station in the AF (Alternative Frequencies) list. If the preset station and the stations in the AF list cannot be received: The unit searches again for a station in the PI (Programme Identification) list. If there are still no stations receivable in the area, the unit displays the frequency of the preset station and the preset indicator disappears. If the signal level of the Regional (Local) station being tuned becomes too weak to receive, press the same F1 through F6 buttons to tune in a Regional station in other district. NOTE For presetting the RDS stations, refer to the Radio Operation section. The RDS stations can be preset in the FM1, FM2 and FM3 bands only. Press the F button so that the FUNC indicator will illuminate. Press the F1 (AF) button to activate the RDS mode. Press the DN g or f UP button to tune in the desired RDS station. NOTE When the BAND button is pressed and held for more than 2 seconds while a station name is displayed, the display shows the station frequency for 5 seconds. When the RDS station signal received has become weak: AF seek mode, press and hold the F1 (AF) button for at least 2 seconds to have the unit automatically seek a stronger station in the AF list. If there is no AF station, the display shows "SEEK END. " 5 4 5 Press the F1 button again to deactivate the RDS mode. Press the F button to activate the normal mode. The FUNC indicator will turn off. 14-EN Receiving RDS Regional (Local) Stations 1 2 Press and hold the INTLZ button for at least 2 seconds to activate the setting mode. Press the f UP button repeatedly to select "REG. (REGIONAL)" Each press of the f UP button scrolls the modes as shown: FM-LE REG PTY31 AMBER DIM SUB BEEP D-OUT CLOSE DEMO AUX SCR MUTE NOTE If you press the DN g button the display scrolls in reverse sequence. NOTES · If the traffic information broadcast signal falls below a certain level, the unit remains in the receiving mode for 1 minute. [. . . ] 6 Power Antenna Lead (Blue) Connect this lead to the +B terminal of your power antenna, if applicable. NOTE This lead should be used only for controlling the vehicle's power antenna. Do not use this lead to turn on an amplifier or a signal processor, etc. Fuse Holder (7. 5A) Battery Lead (Yellow) Connect this lead to the positive (+) post of the vehicle's battery. ISO Power Supply Connector Ground Lead (Black) Connect this lead to a good chassis ground on the vehicle. [. . . ]