User manual ALPINE CDA-9854R

[. . . ] FOR CAR USE ONLY/NUR FÜR AUTOMOBIL GEBRAUCH/POUR APPLICATION AUTOMOBILE UNIQUEMENT/ PARA USO EN AUTOMÓVILES/SOLO PER L'UTILIZZO IN AUTOMOBILE/ENDAST FÖR BILBRUK R RDS MP3/WMA CD Receiver EN CDA-9854R CDA-9852RB CDA-9852RR · OWNER'S MANUAL Please read before using this equipment. · BEDIENUNGSANLEITUNG Lesen Sie diese Bedienungsanleitung bitte vor Gebrauch des Gerätes. · MODE D'EMPLOI Veuillez lire avant d'utiliser cet appareil. · MANUAL DE OPERACIÓN Léalo antes de utilizar este equipo. [. . . ] * When the subwoofer mode is set to OFF, its level cannot be adjusted. 2 Turn the Rotary encoder until the desired sound is obtained in each mode. By setting Defeat ON, previously adjusted settings of BASS and TREBLE will return to the factory defaults. · Depending on the connected devices, some functions and display indications do not work. 14-EN Setting the Bass Control You can change the Bass Frequency emphasis to create your own tonal preference. Bass level indicator's display Bass level is usually displayed. 1 2 Press MENU to select the BASS ENGINE mode, then press MODE. BASS ENGINE SETUP RETURN (OFF) BASS ENGINE Press or to select the BASS (bass Centre frequency) control mode. BASS TREBLE Setting the Treble Control You can change the Treble Frequency emphasis to create your own tonal preference. Setting the Bass Centre Frequency 3-1 Press SOURCE/POWER to select the desired bass centre frequency. 80Hz 100Hz 120Hz 60Hz 80Hz 1 2 Press MENU to select the BASS ENGINE mode, then press MODE. BASS ENGINE SETUP RETURN (OFF) BASS ENGINE Emphasizes the displayed bass frequency ranges. Setting the Bass Bandwidth Press or to select the TREBLE (treble Centre frequency) control mode. BASS TREBLE 3-2 Press BAND to select the desired bass bandwidth. (Narrow) (Wide) Setting the Treble Centre Frequency 3-1 Press SOURCE/POWER to select the desired treble Centre frequency. 10. 0kHz 12. 5kHz 15. 0kHz 7. 5kHz 10. 0kHz Changes the boosted bass bandwidth to wide or narrow. A wide setting will boost a wide range of frequencies above and below the centre frequency. A narrower setting will boost only frequencies near the centre frequency. Emphasizes the displayed Treble frequency ranges. Setting the Treble Level Setting the Bass Level 3-2*2Turn the Rotary encoder to select the desired treble level (­7~+7). You can emphasize the treble level. 3-3*1Turn the Rotary encoder to select the desired bass level (­7~+10). You can emphasize or weaken the bass level. 4 Press MENU to select RETURN. After 2 seconds, the unit returns to normal mode. Pressing and holding MENU for at least 2 seconds will return to normal mode. 4 Press MENU to select RETURN. After 2 seconds, the unit returns to normal mode. Pressing and holding MENU for at least 2 seconds will return to normal mode. · If no operation is performed within 60 seconds, the bass control setting will be turned off automatically. · The bass level settings will be individually memorized for each source (FM, MW (LW), CD, etc. ) until the setting is changed. The bass frequency and bass band width settings adjusted for one source are effective for all other sources (FM, MW (LW), CD etc. ). · Depending on the connected devices, some functions and display indications do not work. However, Bass Level is still adjustable if an audio processor with the Bass function is connected. · This function is inoperable when DEFEAT is set to ON. · If you press or in the bass control mode, the unit changes to the treble control mode. *1 The adjustment can also be made by pressing MODE. Refer to "Adjusting Bass/Treble/Balance (Between Left and Right)/Fader (Between Front and Rear)/Defeat" (page 14). · If no operation is performed within 60 seconds, the treble control setting will be turned off automatically. · The treble level settings will be individually memorized for each source (FM, MW (LW), CD, etc. ) until the setting is changed. The Treble frequency settings adjusted for one source are effective for all other sources (FM, MW (LW), CD, etc. ). · Depending on the connected devices, some functions and display indications do not work. However, Treble Level is still adjustable if an audio processor with the Treble function is connected. · This function is inoperable when DEFEAT is set to ON. · If you press or in the treble control mode, the unit changes to the bass control mode. *2 The adjustment can also be made by pressing MODE. Refer to "Adjusting Bass/Treble/Balance (Between Left and Right)/Fader (Between Front and Rear)/Defeat" (page 14). 15-EN Turning Loudness On/Off Loudness introduces a special low- and high-frequency emphasis at low listening levels. This compensates for the ear's decreased sensitivity to bass and treble sound. Other Functions Press and hold MODE for at least 2 seconds to activate or deactivate the loudness mode. "LD" indicator lights. TITLE Displaying the Text Text information, such as the disc name and the track name, will be displayed if playing a CD text compatible disc. [. . . ] For details on connection, refer to the Owner's Manual of the KCA-420i. Antenna Receptacle Audio Interrupt In Lead (Pink/Black) Connect this lead to the Audio Interface output of a cellular phone which provides ground shorting when a call is received. Steering Remote Control Interface Connector To steering remote control interface box. For details about connections, consult your nearest Alpine dealer. Remote Turn-On Lead (Blue/White) Connect this lead to the remote turn-on lead of your amplifier or signal processor. Fuse Holder (10A) Rear Output RCA Connectors (CDA-9854R only) RED is right and WHITE is left. Dimmer Lead (Orange) This lead may be connected to the vehicle's instrument cluster illumination lead. This will enable the vehicle's dimmer control to dim the backlighting of the unit. Front Output RCA Connectors (CDA-9854R only) RED is right and WHITE is left. Switched Power Lead (Ignition) (Red) Connect this lead to an open terminal on the vehicle's fuse box or another unused power source which provides (+) 12V only when the ignition is turned on or in the accessory position. CDA-9854R: Subwoofer Ouput RCA Connectors CDA-9852RB/CDA-9852RR: Front/Subwoofer*3 Output RCA Connectors *3 When Subwoofer is set to OFF:Output is from front speakers. When Subwoofer is set to ON:Output is from Subwoofer. [. . . ]