User manual ALPINE NVE-N099P

[. . . ] PRECAUTIONS GUIDE FOR INSTALLATION AND CONNECTIONS FOR AUTHORIZED ALPINE DEALERS · Please read this GUIDE FOR INSTALLATION AND CONNECTIONS FOR AUTHORIZED ALPINE DEALERS and the OWNER'S MANUAL thoroughly to familiarize yourself with each control and function. We at ALPINE hope that your new NVE-N099P will give you many years of enjoyment. In case of problems when installing your unit, please contact your authorized ALPINE dealer. BEFORE WIRING, DISCONNECT THE CABLE FROM THE NEGATIVE BATTERY TERMINAL. [. . . ] NVE-N099P Wiring Diagram With CVA-1000R/TME-M006SP/ TME-M005P 4. Installing TMC antenna 2 5 6 7 8 9 10 11 12 13 4 1. Preparation 1 Check accessory parts. GPS aerial (5 m) Aerial mounting plate ×3 Cable clamp Parking brake aux. cord ×2 Solderless connector Remote control ×2 Remote control holder (2. 5 m) Power cables 1 Bracket (4. 5 m) 13P RGB extension cable (6 m) Extension cables 2 Floor base 3 Screw with double washer (M4 × 8) ×4 Battery (AAA) 5 Flanged self-tapping screw (M5 × 15) ×4 4 Hex bolt (M6 × 50) ×4 One each for left and right 6 Spring washer (M6) ×4 7 Flanged hex nut (M6) ×4 ×2 8 Wing nut (M6) 9 Velcro fastener !Velcro tape ×2 " Self-tapping screw (M3 × 12) ×4 ×4 Note: · For further details about accessory parts for the TMC antenna, refer to "6. Installing TMC antenna"(page 13). 2 Prepare tools and mounting information. Screwdriver Electrical tape Pliers Mounting the aerial inside the vehicle. Mount the aerial. Spanner Pencil and eraser Aerial 3 Park the vehicle in a safe and level location. 4 5 Apply the brake and remove the ignition key. Clean dust and oil at the mounting location and mount the aerial. Aerial Notes: · Mount the aerial on a flat plane of the dash board or rear tray. · Some thermal reflection type or thermal absorption type glass may interrupt high frequency waves. If reception is poor with the aerial installed inside the car, try to mount the aerial outside the car. 6 Routing the aerial cable. Route the cable using the provided cable clamps to take up the cable's slack. Use the waterproof pad when running the cable under the vehicle's rubber gasket. Attach the cable at several points using the remaining cable clamps. Notes: · The magnet of the aerial is very strong. Proceed cautiously to prevent any damage to the vehicle's body. Keep the magnet away from articles susceptible to magnetic fields such as credit cards, watches, etc. Reception sensitivity may be decreased. Water proof pad Cable clamp 5 2. Connections 1 Disconnect the battery (­) terminal. 4 Wrap electrical tape around end of leads not used. Note: Some vehicles contain a vehicle control computer etc. in this case, contents of the computer memory may be erased when the battery (­) lead is disconnected. 5 2 Cut terminal leads as required, and attach the solderless connectors to the leads. Note: For leads which need branching to the speed sensor, dimmer, parking brake, etc. , use the solderless connectors. Connect the battery (­) terminal and turn the ignition key to the ACC or ON position. Check to see if operation can be performed properly. Is the illumination turned on?) You can check the language selection menu with the monitor. (Refer to the Owner's Manual for details. ) Go to step 6 after checking is completed. ON Preparation Navigation side lead 6 1 Solderless connector (supplied with the unit) Vehicle lead Turn the ignition key to the OFF position to turn off the power after completion of the check. OFF Navigation side lead Stopper 7 Pull out the ignition key and remove the battery terminal (­) again to begin installation procedure. 2 Pliers 3 Connect the power lead to this unit. Insert until a click sound is heard. 6 3-1. [. . . ] 2 3 1 4 Mount the unit on the carpet with spring washers (M6) 6 and wing nuts (M6) 8. Continued to step 5 "Securing leads, etc. " 8 3 6 2 Determine mounting position of the floor bases 2 for placement under the carpet. 8 6 5 6 2 Securing leads, etc. Make sure leads are not pinched by moving parts such as the seat rail, etc. Also check for damaged from sharp edges or protrusion. [. . . ]