User manual ALPINE TME-M680

[. . . ] 6-8 Fiveways Boulevarde Keysborough, Victoria 3173, Australia Tel. : (03) 9769-0000 ALPINE ELECTRONICS GmbH Frankfurter Ring 117 80807 Munich, Germany Tel. : 089-32 42 640 ALPINE ITALIA S. p. A. Colombo 8, 20090 Trezzano Sul Naviglio MI, Italy Tel. : 02-48 47 81 ALPINE ELECTRONICS (BENELUX) GmbH Leuvensesteenweg 510-B6, 1930 Zaventem, Belgium Tel. : 02-725 1315 ALPINE ELECTRONICS FRANCE S. A. R. L. (RCS PONTOISE B 338 101 280) 98, Rue De La Belle Etoile, Z. I. 50016 F-95945, Roissy, Charles De Gaulle Cedex, France Tel. : 01-48 63 89 89 ALPINE ELECTRONICS OF U. K. , LTD. [. . . ] After turning the system off, a slight ghost of the image will remain temporarily. This is an effect peculiar to LCD technology and is normal. Under cold temperature conditions, the screen may lose contrast temporarily. After a short warm-up period, it will return to normal. · · Adjusting the Volume 1 Adjust the volume level by pressing the button. or 4-EN Switching the display mode Adjusting 1 Press the DISP button. Each press of the button will cycle through the modes as follows. WIDE NORMAL ZOOM 1 2 Press and hold the DISP button for at least 2 seconds. Press the DISP button and select the mode to be adjusted. Adjust by pressing the DISP or : Selects the mode. (downward) : Adjusts. WIDE Normal images are expanded uniformly in the horizontal direction and are displayed over the entire screen. Normal image (4:3) 1 Brightness adjustment (BRIGHT) SETUP MENU 12 NORMAL ZOOM Normal images are expanded in the horizontal direction and are displayed over the entire screen. The expansion ratio increases towards the right and left edges of the screen. Allows the brightness (0 to 32) of the picture 2 Contrast adjustment (CONTRAST) SETUP MENU 16 Contrast can be adjusted from 0 to 32 3 Color depth adjustment (COLOR) SETUP MENU 32 Color depth can be adjusted from 0 to 32 5-EN Basic Operation 4 Dimmer adjustment (DIMMER) SETUP MENU Other Useful Feature Remote Control Sensor 10 The backlighting is set to the value adjusted at 0~10 5 IR-TX adjustment (IR-TX) SETUP MENU Remote sensor · Receives the remote control signal from connected ALPINE products such as DVD players and TV tuners. ON OFF ON : Enable to use IR Headphone 6 Reset or to restore system setting to Press factory detault. 7 Exit Select EXIT to exit setup menu, and the screen will return to normal mode. 3 After completing adjustments, press and hold the DISP button for at least 2 seconds. The screen will return to the normal mode. · If no operation is made for 5 seconds after selecting a mode to be adjusted, the adjustment mode will be cleared. 6-EN Information In Case of Difficulty If you encounter a problem, please review the items in the following checklist. This guide will help you isolate the problem if the unit is at fault. Otherwise, make sure the rest of your system is properly connected or consult your authorized Alpine dealer. Information Specifications MONITOR 5. 8" Low reflection rear projection type TN liquid crystal panel Drive System Active matrix drive, normally white display Number of Picture Elements 400(W) x 234(H) x 3 Effective Number of Picture Elements 99. 99% or more Light Source Internal optical system (U-type cold cathode fluorescent tube) Dimensions (W x H x D) 153 x 102 x 20mm Weight 255g Screen Size Display System No function or display. · Car's ignition is off. · Vehicle's battery is weak. - Check the voltage of vehicle's battery. Black box Dimensions (W x H x D) Weight 177 x 103 x 28 mm 400g No picture display. · Brightness control is set for minimum brightness control. · Incorrect setting of the VTR mode. · Protective circuit is on because of high temperature. - Wait until the temperature inside the vehicle comes down to the operating temperature range (45°C). · Incorrect or open connection with the Monitor, AV interface unit. · Due to continuous product improvement, specifications and design are subject to change without notice. · The LCD panel is manufactured using an extremely high precision manufacturing technology. [. . . ] AUX3 SELECTION S/W "OUT" position Audio input / output connectors Use these connectors to output the audio signals to other products. Video input / output connector Use this connector to output the video signals to other products. To prevent external noise from entering the audio system. · Locate the unit and route the leads at least 10 cm away from the car harness. [. . . ]