User manual ALPINE TMX-R680A

[. . . ] 133, Spain Tel. : 34-45-283588 Printed in U. S. A INSTALLATION INSTRUCTION # ALA440089 Printed in U. S. A 8 26. Raise monitor housing into approximate position and connect all wiring to components. Connect wiring and cabling per instructions included with LCD monitor. Caution: Check for clearance of dome light switch terminals and other wiring to prevent possibility of a short circuit. [. . . ] Install dome light switch (item 13 pg 3) in opening in front of console. 7 22. To determine the length of spacers (item 9 pg 3) and screws that will be needed, place a straight edge across the console and measure to each mounting boss as shown. Mark each spacer and screw appropriately, then trim to measured length. See Photo 8. 4 5 6 7 8 9 10 11 12 13 14 SPLIT LOCK WASHER, # 8 PUSH ON RETAINER FENDER WASHER NUT, 8-32, KEPS SCREW, 8-32 X 3 1/2" PPH PLASTIC SPACER, 1/4" X 1/2" X 3" MOUNTING BRAKET CONSOLE, VINYL COVERED CONSOLE, PLASTIC ONLY SWITCH, SPDT CONSOLE MOUNTING BRACKET 4 4 4 4 4 4 1 1 1 1 1 Caution: If screws extend more than 1" past the edge of console, PHOTO 7to roof of vehicle damage may occur. If spacers and screws are different lengths, be sure make note of proper location for correct installation. Release LCD monitor panel from locked position. Lower to viewing position to access mounting locations. Install (4) four proper length 8-32 screws (item 3 or 8 pg 3), (4) four # 8 lock washers (item 4 PHOTO 8 pg 3), and (4) four plastic spacers (item 9 pg 3) previously cut. Place fender washer (item 6 pg 3) and push on retainer (item 5 pg 3) over screws as shown. PREPARATION OF VEHICLE INTERIOR MATERIALS PROVIDED FOR INSTALLATION: ITEM Description SCREW, 8-32 X 3/8" PPH 1 PHOTO 9 6 SCREW, #10 X 3/4" HWH SCREW, 8-32 X 1 1/2" PPH PHOTO 10 QTY 4 1. Determine which console is to be used, the low profile vinyl covered console (item 11 pg 3) for relatively flat headliners or high profile plastic only console (item 12 pg 3) for heavily contoured headliners. Insert the TMX-R680A LCD monitor in the console and secure using (4) four screws provided with monitor. 3 See Photo 1. 2 3 4 4 3. Release LCD monitor panel from locked position. Determine a suitable mounting location by raising console into approximate position and checking the viewing angle from the rear seat, contours in headliner, that THE MONITOR CAN NOT BE VIEWED BY THE DRIVER, AND THAT THE MONITOR WILL NOT IMPROPERLY LIMIT REAR VIEW MIRROR FUNCTIONS. ENSURE COMPLIANCE WITH ALL APPLICABLE SAFETY STANDARDS GOVERNING THE FUNCTION OF THE REAR VIEW MIRROR, THE 12. Using an analog or digital multi-meter, test the function of the dome lights. Install and route all video and audio cables, and any other added component requirements to their respective places in the vehicle. Refer to component installation instructions for wiring diagrams. The suggested routing of the video system cable is as follows: Above the headliner from video system to the B-pillar. Connect per instructions included with the video system and the TMX-R680A owner's manual. 5. 8. DRIVER'S FIELD OF THE VIEW AND THE PHOTO 1 PASSENGER'S SAFETY. Mark location on headliner with masking tape. [. . . ] Make necessary adjustments to the mounting bracket assembly and install in vehicle. Use additional screws and nuts (items 1 & 7 pg 3) if necessary. Make sure that bracket is centered left to right and secure using (4) four # 10 x 3/4" screws (item 2 pg 3). Caution: Make sure that roof brace is at least 3/4" tall. [. . . ]