User manual ALTEC LANSING 416-8C LF SPEAKER

[. . . ] NÄR DENNA DEL ÄR ÖPPNAD OCH UND VORSICHT UNSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG GEÖFFNETAUSSETZEN. VARNING OSYNLIG LASERSTRÅLNING FARLIG. STRÅLEN ÄR SICHERHEITSVERRIEGELUNG ÜBERERÜCKT. NICHT DEM STRAHL AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET ALTTIINA NÄKYMÄTÖNTÄ USYNLIG LASERSTRÅLING VED ÅBNING, NÅR SIKKERHEDSAFBRYDERE ER ADVARSEL UDE AF FUNKTION. [. . . ] · When using two-sided invoice size originals from the SPF/RSPF, be sure to place them in the landscape orientation. Otherwise, an original misfeed will occur. AA 1 2 A A A A A A Turn on Long Edge Turn on Short Edge Making two-sided copies Place the original on the original table or in the SPF/RSPF. (see "ORIGINAL PLACEMENT" (p. 47). Select two-sided copy mode. 52 A: When copying in a one-sided to two-sided mode: Use the original to copy key to select the desired one-sided to two-sided copying mode (Turn on Long Edge or Turn on Short Edge). B: When copying in the two-sided to two-sided mode: Use the original to copy key to select the two-sided to two-sided copying mode. The originals must be set in the SPF/RSPF before this mode can be set (step 3) on page 48 (AL-1555). C: When copying in the two-sided to one-sided mode: Use the original to copy key to select the two-sided to one-sided copying mode. The originals must have been set in the SPF/RSPF in step 3 on page 48 (AL-1555). A B C 3 Select the copy settings. See "SET THE COPY QUANTITY" (p. 49), "EXPOSURE ADJUSTMENT/PHOTO COPYING" (p. 49), and "REDUCTION/ENLARGEMENT/ZOOM" (p. 51). Using the original table If you are using the original table, copying is only possible in one sided to two-sided mode ("A" above). The original is scanned into the unit's memory. 2 Place the original that you wish to copy onto the rear side of the paper, and press the start ( ) key again. 4 OFF, *1 OFF, *1 300dpi, 1 60sec. , 2 5min. , 2 60 min. 120min. * Factory default settings are indicated with an asterisk (*). 4 can be selected on when your unit has the SPF/ RSPF. 5 Press the start ( ) key. The right-hand number in the display will be steadily lit and the entered value will be stored. To change the setting or to set another mode, press the clear ( ) key. The unit will return to step 2. 6 Press the light ( copy mode. ) or dark ( ) key to return to the normal DISPLAYING TOTAL NUMBER OF COPIES Use the following procedure to display the total number of copies. Press and hold down the clear ( ) key for approximately 5 seconds. The total number of copies will appear in two steps, each with three digits. Example: Total number of copies is 1, 234. 56 7 MAINTENANCE This chapter describes how to replace the TD cartridge and drum cartridge, and how to clear the unit. Be sure to use only genuine ALTEC LANSING parts and supplies. TD CARTRIDGE REPLACEMENT The TD cartridge replacement required ( ) indicator will light up when toner is needed. For more information on purchasing the TD cartridge, see "ABOUT SUPPLIES AND OPTIONS" (p. 70). If copying is continued while the indicator is lit, copies will gradually become lighter until the unit stops and the indicator begins blinking. Replace the old TD cartridge by following the procedure below. [. . . ] Skin Protection : Not required under intended use. Other Protective Equipment : Use of a dust mask and goggles are recommended when handling a large quantity of toner or during long term exposure, as with any non-toxic dust. MATERIAL SAFETY DATA SHEET Page: 3/4 Date Revised: Jul. F-30831 9. PHYSICAL AND CHEMICAL PROPERTIES Appearance Physical State : Solid Form : Powder Color : Black Ph : Not applicable Boiling / Melting Point : Not applicable Flash Point(°C) : Not applicable lgnition Point(°C ) : No data Explosion Properties : No data Density(g/cm³) : 5. 4 (bulk density : 2. 09) Solubility in Water : Negligible Odor : odorless 10. STABILITY AND REACTIVITY Stability Hazardous Reactions Conditions to Avoid Materials to Avoid Hazardous Decomposition Products Further Information : Stable : Dust explosion, like most finely divided organic powders. : Electric discharge, throwing into fire. [. . . ]