User manual ALTEC LANSING 420A LF SPEAKER

[. . . ] Should the fuse need to be replaced, a BSI or ASTA approved fuse to BS1362 marked or and of the same rating as the one removed from the plug must be used. Always refit the fuse cover after replacing the fuse on the moulded plug. Never use the plug without the fuse cover fitted. In the unlikely event of the socket outlet in your home not being compatible with the plug supplied either cut-off the moulded plug (if this type is fitted) or remove by undoing the screws if a rewireable plug is fitted and fit an appropriate type observing the wiring code below. [. . . ] Take care not to burn yourself. Do not block the ventilation ports on the machine. For best copying results, be sure to use only Sharp Genuine Supplies which are designed, engineered, and tested to maximize the life and performance of Sharp products. Look for the Genuine Supplies label on the toner package. GENUINE SUPPLIES Storage of supplies Proper storage 1. Store the supplies in a location that is: · clean and dry, · at a stable temperature, · not exposed to direct sunlight. Store paper in the wrapper and lying flat. Paper stored in packages standing up or out of the wrapper may curl or become damp, resulting in paper misfeeds. Storing toner cartridges Store a new toner cartridge box horizontally with the top side up. Do not store a toner cartridge standing on end. If stored standing on end, the toner may not distribute well even after shaking the cartridge vigorously, and will remain inside the cartridge without flowing out. Staple cartridge The finisher require the following staple cartridge: MX-SCX1 (for finisher) Approx. 5000 per cartridge x 3 cartridges Supply of spare parts and consumables The supply of spare parts for repair of the machine is guaranteed for at least 7 years following the termination of production. Spare parts are those parts of the machine which may break down within the scope of the ordinary use of the product, whereas those parts which normally exceed the life of the product are not to be considered as spare parts. Consumables too, are available for 7 years following the termination of production. 9 Emission of noise and chemicals Noise emission values Noise emission values as measured according to ISO7779 are listed to the right. Next, select a language to download the file in from the [Language] list and then click on the [Download] button. Double-click on the downloaded file to display the Operation Guide. 14 SPECIFICATIONS Basic Specifications / Copier specifications Name Type Colour Copier system 420A LF SPEAKER Desktop Full colour Laser electrostatic copier Scan (B/W): 600 × 600 dpi, 600 × 400 dpi, 600 × 300 dpi Scanning resolution Scan (full colour): 600 × 600 dpi Print: 600 × 600 dpi, equivalent to 9, 600 dpi × 600 dpi Gradation Original paper sizes Scan: equivalent to 256 levels / Print: equivalent to 256 levels Continuous copy Max. A3 (11"×17") / sheets, bound documents Standard: 1 GB HDD: 160 GB A3 wide (12" × 18") to A5R, 5-1/2" × 8-1/2"R, Transparency film, Heavy paper, Envelopes Tray 1-4: A3, B4, A4, A4R, B5, B5R, A5R, 11" × 17", 8-1/2" × 14", 8-1/2" × 13-1/2", 8-1/2" × 13-2/5", 8-1/2" × 13", 8-1/2" × 11", 8-1/2" × 11"R, 7-1/4 × 10-1/2"R, 5-1/2" × 8-1/2"R Copy sizes Multi-bypass tray: A3 wide (12" × 18") to A5R, 5-1/2" × 8-1/2"R, Transparency film, Heavy paper, Envelopes Lost margin (leading edge): 4 mm (11/64") ± 1 mm (± 3/64) Lost margin: (trailing edge): 2 mm (6/64") - 5 mm (- 13/64) Leading edge / trailing edge: total 8 mm (21/64") or lessNear edge / far edge: total 4 mm (11/64") ± 2 mm (± 6/64") or less Warm-up time 20 seconds or less This may vary depending on the ambient conditions. Full colour : 10. 0 seconds B/W: 7. 4 seconds This may vary depending on the state of the machine. A4, 8-1/2" × 11" A4R, 8-1/2" × 11"R Continuous copying speeds* (when shifter is not in operation) B4, 8-1/2" × 14" A3, 11" × 17" B5 B5R 23 copies/min. Overall dimensions Dimensions Weight Required power supply Ambient environment 10 °C (54 °F) to 35 °C (91 °F) (20 % to 60 % RH) 10 °C (54 °F) to 30 °C (86 °F) (85 % RH) Local voltage ± 10 % (For the power supply requirements, see the name plate in the lower corner of the left side of the machine. ) Power consumption Max. 1. 84 kW (220-240 V) / 1. 44 kW (100-127 V) (including options such as the desk) 583 mm (W) × 623 mm (D) × 834 mm (H) (22-61/64" (W) × 24-34/64" (D) × 32-53/64 (H)) Approx. 73 kg (160 lbs. ) 851 mm (W) × 623 mm (D) (33-32/64" (W) × 24-34/64" (D)) (With multi-bypass tray extended) 964 mm (W) × 623 mm (D) (37-61/64" (W) × 24-34/64" (D)) (With right side exit tray extended) Storage 1 GB = One billion bytes when referring to hard drive capacity. capacity 2, 100 sheets in 4 trays (500 × 4) plus 100-sheet multi-bypass tray Using 80 g/m2 (21 lbs. ) weight paper Paper feed / capacity 500 sheets in one tray plus 100-sheet multi-bypass tray Using 80 g/m2 (21 lbs. ) weight paper Copy rations Same size: 1:1 ± 0. 8 % Enlarge: 115 %, 122 %, 141 %, 200 %, 400 % Reduce: 25 %, 50 %, 70 %, 81 %, 86 % Zoom range: 25 to 400 % (25 - 200 % using RSPF) in 1 % increments, total 376 increments. First-copy time * Continuous speed for same original source. Output may be temporarily interrupted to stabilize image quality. 15 SPECIFICATIONS Automatic document feeder (Standard equipment) Name Document feeder types Original paper sizes Original paper types Two-sided Reversing Single Pass Feeder (RSPF) Reversing Single Pass Feeder (RSPF) A3 (11" × 17") to A5 (5-1/2" × 8-1/2") Paper weight Thin paper 35 g/m2 (9 lbs. ) to 49 g/m2 (13 lbs. ) Plain paper 50 g/m2 (13 lbs. ) to 128 g/m2 (32 lbs. ) 50 g/m2 (13 lbs. ) to 105 g/m2 (28 lbs. ) Scan speed (copy) Paper storage capacity 100 sheets (80 g/m2 (21 lbs. )) (or maximum stack height of 13 mm (33/64")) B/W: 50 one-sided sheets/minute (A4 (8-1/2" × 11") horizontal) (600 × 400 dpi) Colour: 36 one-sided sheets/minute (A4 (8-1/2" × 11") horizontal) (600 × 600 dpi) Tray Name Paper sizes Useable paper Paper capacity Tray 1 (MX-DE12) Tray 2 (MX-DE13) Tray 3 (MX-DE14) Dimensions 583 mm (W) × 577 mm (D) × 382 mm (H) (22-61/64" (W) × 22-46/64" (D) × 15-1/64" (H)) MX-DE12: Approx. 21 kg (46 lbs. ) Weight 1, 500 (500 × 3) MX-DE13: Approx. 28 kg (61 lbs. ) A3 (11" × 17") to A5R (5-1/2" × 8-1/2"R) 60 g/m2 (16 lbs. ) to 209 g/m2 (56 lbs. ) 500 sheets 1, 000 (500 × 2) Finisher Name Paper sizes Useable paper No. [. . . ] · Sharp OSA is a trademark of Sharp Corporation. · RealVNC is a trademark of RealVNC Limited. · All other trademarks and copyrights are the property of their respective owners. Candid and Taffy are trademarks of Monotype Imaging, Inc. [. . . ]