User manual ALTEC LANSING 815A LF SPEAKER CABINET

[. . . ] 6 Installing batteries in the remote control unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Watching TV Watching a TV programme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Operating the TV buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Useful features Channel/Timer display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Incorrect installation of the batteries may damage the remote control. E6 ENGLISH Part names Part names TV set Bottom 8 POWER 8 / Volume up/down buttons Adjusts the volume. Makes adjustments in PRESET. POWER switch Turns on and off the main power. 8 Power indicator Power can be turned on by the remote control when the indicator is dimly. 8 CH / CH Channel up/down buttons Selects the channels. Tunes or sets the channels. Infrared sensor window Receives the infrared wave from the remote control. 6 9 Headphone jack Use to listen to the audio with headphone. MENU/PRESET 12 MENU/PRESET button Tunes the channels. Used for MENU setup. 23 Audio input terminal (AV-2) Connects to a camcorder, video game, etc. 23 Video input terminal (AV-2) Connects to a camcorder, video game, etc. · When using headphone, see 9. E7 Watching a TV programme Simple operations for watching a TV programme TV Set (Bottom) 1 Turn on power. · When the power indicator is off, press POWER . · When the power indicator lights up dimly, press on the remote control. The power indicator changes to bright and a picture appears. POWER Power indicator 2 Select channel. With CH / CH CH CH · Press CH and channels change as shown below. · Press CH and channels change as shown below. / 2 / 1 / 0 . . . With the number buttons (on remote control) 5 · To select a one-digit channel, such as 5, press . If "5-" is indicated, press to select one-digit input, and then 5 press again. · To select a two-digit channel, such as 15, press to select 1 5 the two-digit input. Press , and then press . TV/VIDEO 1 1 4 7 2 5 8 0 3 6 9 5 CH CH CH CH FEATURE CH-SET TIMER NORMAL PICTURE -115 PAL B/G 3 TV Adjust volume using . / · The number of oval blocks " " indicates the volume level. · FINE The frequency changes to allow fine tuning. 4 Press CH-SET to return to normal screen. · When you select AV1 or AV2 for the channel position, the CH-SETTING screen changes as shown on the right and the colour mode changes in the following order: AUTO PAL SECAM N443 CH-SETTING POSITION COLOUR AV1 AUTO CH :SELECT :ADJUST N358 · Switching COLOUR system: Set the system to "AUTO" for normal TV reception. The AUTO mode automatically detects the receiving signal system and changes the reception system of the TV set. When the picture is not stable, switching to an appropriate system may improve the picture quality. · In a weak reception area, or under bad reception conditions, you can change the frequency by fine tuning. · When using FINE, the channel number changes from green to yellow. · To return the channel to its original frequency setting, follow the manual channel tuning procedure. See 15 . E 16 ENGLISH Settings and adjustments Picture adjustment TV/VIDEO 1 2 CH CH Press PICTURE screen. to call PICTURE PICTURE CONTRAST COLOUR BRIGHTNESS TINT ALTEC LANSINGNESS WHITE TEMP 50 0 +10 -10 1 4 7 2 5 8 0 3 6 9 Press CH / CH select adjustment items. to CH CH 3 Adjust using / . · Wait for approximately three seconds to return to PICTURE menu. PICTURE FEATURE CH-SET TIMER NORMAL PICTURE NORMAL TV CONTRAST - 50 + 4 5 Repeat steps 2 and 3 above to adjust other items. Press PICTURE to return to normal screen. · Pressing NORMAL while a PICTURE selection is displayed, only the selected mode is reset to the standard (factory-setting) position. · Pressing NORMAL while a PICTURE menu screen is displayed will reset all the items of PICTURE menu to the standard (factory-setting) position. The following table lists the adjustment items shown in the PICTURE menu and how they change as you press / . Selected item CONTRAST COLOUR BRIGHTNESS TINT ALTEC LANSINGNESS WHITE TEMP Press To decrease contrast For less colour intensity For less brightness To move tint toward red For less sharpness To more reddish background Press - + + + - + To increase contrast For more colour intensity For more brightness To move tint toward green For more sharpness To more bluish background *: TINT can only be selected and adjusted when receiving NTSC broadcasts. (AV only) E 17 Blue screen Automatically turns the screen blue if a broadcast signal is not received. TV/VIDEO 1 2 3 Press FEATURE to call FEATURE screen. Press / to select "BLUE BACK" to "ON" or "OFF". FEATURE BLUE BACK ON 1 4 7 2 5 8 0 3 6 9 :ADJUST CH CH Press FEATURE to return to normal screen. FEATURE CH-SET TIMER NORMAL PICTURE When BLUE BACK is set to "ON" No signal Blue screen TV off (Indicator) FEATURE TV after 5 seconds after 15 minutes Standby mode Power indicator lights up dimly · Poor reception due to weak signals and too much noise may activate BLUE BACK, despite the presence of a broadcast signal. [. . . ] · The right example shows that the Reminder will be activated after one hour 50 minutes. TV CH :SELECT :ADJUST 4 Press TIMER to return to normal screen. · Five minutes before the preset length of time expires (in the example, after one hour and 45 minutes) and each minute thereafter, the remaining time appears on the screen for several seconds. · When the preset length of time has passed, " 0:00" flashes in red. 0:05 0:04 0:03 0:02 0:01 0:00 Flashing · This function also works in the Standby mode. Power is automatically turned on five minutes before the preset length of time expires. The TV set automatically returns to the Standby mode approximately 1 minute after the timer expired if no buttons are pressed on the TV set or remote control. [. . . ]