User manual ALTEC LANSING 95-BK SPEAKER SYSTEM

[. . . ] During Continuous Run Mode, press Wrinkle Prevent + Dry Level for 7 seconds to return to normal user mode. Service Mode Definition of Service Mode - Dryer must be on before Service Mode can be entered. - Upon entry into Service Mode, the Sensor Bar Touch Data will be shown (Default Service Mode). How to Enter: - To enter Service Mode, press Wrinkle Prevent and Temp Keys for 3 seconds, until it sends out a beeping sound. [. . . ] Software Version Mode Definition of Software Version Mode: - It is to retrieve its software version How to Enter: - At Service Mode, press Temp until it sends out a beeping sound ex) In case of “U0 05”, U0 means major version “U0” 05 means minor version “05” - If press Temp key In Software Version Mode, it will return Service Mode. 3 Technical_information-03044A-02_EN. Indd 3 2012-04-21 �� 10:01:26 ALIGNMENT AND ADJUSTMENTS WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to dryer before servicing, unless testing requires power. Data Display Mode Definition of Data Display Mode: - Display Mode 1 : Temperature data(Celsius) - Display Mode 2 : Average Touch Sensor data for 1 minute - Display Mode 3 : Average Temperature(Celsius) data for 1minute How to Enter: - With Power On, press AdjustUp Key + AdjsutDown Key for 7 seconds until it sends out a beeping sound . - If not pressed any keys for 5 minutes, it will be set back from Data Display Mode - If pressing AdjustUp Key in this mode, Display Mode will be increased. - System Check Mode(t2 mode) Progress Function Performed Start/Pause Motor(CW) Relay On  Heater Relay On  Heater Relay Off, Motor(CW) Relay Off How to Enter: - While in Power Off, pressing the Dry Level + Power keys simultaneously will put the dryer into the System Check mode 4 Technical_information-03044A-02_EN. Indd 4 2012-04-21 �� 10:01:26 ALIGNMENT AND ADJUSTMENTS WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to dryer before servicing, unless testing requires power. TROUBLE DIAGNOSIS - As the micom dry machine is configured of the complicate structure, there might be the service call. Below information is prepared for exact trouble diagnosis and suitable repair guide. Caution for the Repair and Replacement Please follow below instruction for the trouble diagnosis and parts replacement. 1) As some electronic components are damaged by the charged static electricity from the resin part of dryer or the human body, prepare the human body earth or remove the potential differ ence of the human body and dryer by contacting the power supply plug when the work contacting to PCB is executed. • Thumping Check for loose tumbler baffle , rear tumbler roller(s) worn or misaligned , out-of-round tumbler or high weld seam on tumbler. €¢ Ticking Check for loose wire harness or object caught in blower wheel area. Noisy and/Or 12 • Scraping Check for front or rear bulkhead felt seal out of Vibration position or worn tumbler front bearings. Indd 7 2012-04-21 �� 10:01:26 TROUBLE SHOOTING WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to dryer before servicing, unless testing requires power. Indd 8 2012-04-21 �� 10:01:27 TROUBLE SHOOTING WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to dryer before servicing, unless testing requires power. Indd 9 2012-04-21 �� 10:01:28 TROUBLE SHOOTING WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to dryer before servicing, unless testing requires power. Approx ∞ Ω without laundry Approx 190Ω ± 10% with wet clothes Cycling Thermostat - Disconnect harness and test Blue wire Pin 3 to Red wire Pin 6. approx 10 KΩ at 25 °C/77 °F 10 Technical_information-03044A-02_EN. Indd 10 2012-04-21 �� 10:01:28 TROUBLE SHOOTING WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to dryer before servicing, unless testing requires power. External ground connector Neutral grounding wire (green/yellow) Center silver-colored terminal block screw Neutral wire (white or center wire) ¾” (1. Loosen or remove the center terminal block screw. [. . . ] If converting from a 4-wire electrical system to a 3-wire, the ground strap must be reconnected to the terminal block support to ground the Dryer frame to the neutral conductor. External ground connector Green or bare copper wire of power cord ¾” (1. 9 cm) UL-listed strain relief Center silver-colored terminal block screw Neutral Grounding wire (green/yellow) Neutral wire (white or center wire) 1. Remove the External ground connector screw. [. . . ]