User manual ALTEC LANSING AMPS360 SIGNAL PROCESSING

[. . . ] For information on how to use these, refer to their respective user manuals. You can only connect one external box. Introduction Your LCD Display Front MENU button [MENU] Opens the on-screen menu and exits from the menu. Also use to exit the OSD menu or return to the previous menu. Navigate buttons (Up-Down buttons) Moves from one menu item to another vertically or adjusts selected menu values. [. . . ] PIP MTS/S_Mode Mono Mono Stereo Mono SAP Mono Default Manual Change Every time you press the button, a PIP screen appears. - This fuction does not work for this LCD Display. 31. SWAP Swaps the contents of the PIP and main image. The image in the PIP window will appear on the main screen, and the main screen image will appear in the PIP window. - This fuction does not work for this LCD Display. Mechanical Layout(520DX(N)) Mechanical Layout Introduction Connections Connecting a Computer Using a Power cord with Earth · In the event of failure, the earth lead may cause electric shock. Make sure to wire the earth lead in correctly, before connecting the AC power. When unwiring the earth lead, make sure to disconnect the AC power in advance. Note AV input devices such as DVD players, VCRs or camcorders as well as your computer can be connected to the LCD Display. For detailed information on connecting AV input devices, refer to the contents under Adjusting Your LCD Display. Connect the power cord for your LCD Display to the power port on the back of the LCD Display. There are 3 ways to connect the D-sub to your LCD Display. Choose one of the following: Using the D-sub (Analog) connector on the video card. · Connect the D-sub to the 15-pin, RGB port on the back of your LCD Display and the 15 pin D-sub Port on the computer. Using the DVI (Digital) connector on the video card. · Connect the DVI Cable to the DVI port on the back of your LCD Display and the DVI port on the computer. Connections Using the BNC (Analog) connector on the video card. Note 2. · Select Component for the connection to a DTV Set Top Box using the SOURCE button on the front of the LCD Display or on the remote control. Note · For an explanation of Component video, see your Set Top Box owner's manual. Connections Connecting Using a HDMI Cable Note · Input devices such as digital DVD are connected to the HDMI terminal of the LCD Display using the HDMI cable. You cannot connect a PC to the HDMI terminal. · Connecting Using a DVI to HDMI Cable Note · Connect the DVI output terminal of a digital output device to the HDMI terminal of the LCD Display using a DVI to HDMI cable. However, you will receive the following message for a minute; You can choose to change the screen resolution or stay in the current mode during that time. And if the resolution is more than 85Hz, you will see the black screen because the LCD Display does not support over 85Hz. Note Refer to Specifications > Preset Timing Modes for the resolutions or frequencies supported by the LCD Display. Maintenance and Cleaning 1) Maintaining the LCD Display Case. Clean with a soft cloth after disconnecting the power cord. Troubleshooting · · Do not use benzene, thinner or other flammable substances, or a wet cloth. We recommend that a ALTEC LANSING cleansing agent is used to prevent damage to the screen. 2) Maintaining the Flat Panel Display Screen. Clean with a soft cloth (cotton flannel) smoothly. · Never use acetone, benzene or thinner. (They may cause flaws or deformation of the screen surface. ) · The user will be required to pay costs and related expenses for repairing damages caused. Symptoms and Recommended Actions Note A LCD Display recreates visual signals received from the computer. Therefore, if there is a problem with the computer or the video card, this can cause the LCD Display to become blank, have poor coloring, become noisy, and video mode not supported, etc. [. . . ] Check if a special fluorescent or neon lamp is on in the vicinity. Problems related to MagicInfo Note Making a Bootable USB Flash Disk. Q: A: Making a Bootable USB Flash Disk 1) You can turn a common 512-MB or bigger USB storage media into a bootable disk using a USB bootable disk creation tool. (For example, the HP USB Disk Storage Format Tool) 2) Copies the OS ghost image and executables to your USB disk. 3) Enter the BIOS menu of your set by pressing the F2 key in the BIOS logo screen. [. . . ]