User manual ALTEC LANSING DTS200PIX SPEAKER SYSTEM

[. . . ] Make sure to keep the package box for transporting the product in the future. Unpacking LCD Display Introduction Manuals Quick Setup Guide Warranty Card (Not available in all locations) User's Guide MagicInfo Software CD, MagicInfo Manual CD (Applicable to the DXN-2 model only) Cables Power Cord Others Remote Control (BP59-00138A) Batteries (AAA X 2) (Not available in all locations) BNC to RCA Adaptor Jack (Applicable to the DX-2 model only) Sold separately D-Sub Cable DVI Cable LAN Cable (Used with DXN-2 model only) Introduction Sold separately Wall Mount KIT RGB to BNC Cable BNC to BNC Cable (Applicable to the DX-2 model only) RGB to Component Cable Semi Stand KIT Your LCD Display Front MENU button [MENU] Opens the on-screen menu and exits from the menu. Also use to exit the OSD menu or return to the previous menu. Navigate buttons (Up-Down buttons) Moves from one menu item to another vertically or adjusts selected menu values. Adjust buttons (Left-Right buttons) / Volume buttons Moves from one menu item to another horizontally or adjusts selected menu values. When OSD is not on the screen, press the button to adjust volume. ENTER button [ENTER] Activates a highlighted menu item. SOURCE button [SOURCE] Switches from PC mode to Video mode. Selects the input source that an external device is connected to. Introduction [PC] [DVI] [AV] [Component] [HDMI] [MagicInfo] Note · · The BNC mode will not be activated on the DXN-2 model. [. . . ] Note · · Turn on both your computer and the LCD Display. Contact a local ALTEC LANSING Electronics Service Center to buy optional items. Connecting to Other devices Note · AV input devices such as DVD players, VCRs or camcorders as well as your computer can be connected to the LCD Display. For detailed information on connecting AV input devices, refer to the contents under Adjusting Your LCD Display. The LCD Display 's configuration at the back may vary slightly depending on the LCD Display model. · Connecting AV Devices Connections 1. Connect the Video and [R-AUDIO-L] port of the DVD, VCR or DTV Set-Top Box to the Video and [R-AUDIO-L] LCD Display. Play the DVD, VCR or Camcorder with a DVD disc or tape inserted. Select AV using the SOURCE . Connecting the BNC to BNC cable 1. 2. Connect the BNC/COMPONENT IN [R/Y, G/PB, B/PR] ports on the monitor to the BNC port on the external device using the BNC to BNC cable. Select BNC for the Camcorder connection using the Source button on the front of the LCD Display or on the remote control. Note Applicable to the DX-2 model only. Connecting a DVD Player - Applicable to the DX-2 model only. 1. Connect a set of audio cables between the AV/COMPONENT AUDIO IN [L-AUDIO-R] on the LCD Display and the AUDIO OUT jacks on the DVD player. Connections 2. Connect a Component cable between the BNC/COMPONENT IN [R/Y, G/PB, B/PR] port on the LCD Display and the PR, Y, PB jacks on the DVD player. The figure shown below ("Check Signal Cable") appears on a black background when the LCD Display is working normally even though no video signal is detected: While in the Self-Test mode, the LED power indicator remains green and the figure moves around on the screen. 4. Turn off your LCD Display and reconnect the video cable; then turn on both your computer and the LCD Display If your LCD Display screen remains blank after using the previous procedure, check your video controller and computer system; your LCD Display is functioning properly. Warning Messages You can even view the screen at a resolution of 1920 x 1080. However, you will receive the following message for a minute; You can choose to change the screen resolution or stay in the current mode during that time. If the resolution is more than 85Hz, you will see the black screen because the LCD Display does not support over 85Hz. Note Refer to Specifications > Preset Timing Modes for the resolutions or frequencies supported by the LCD Display. Maintenance and Cleaning 1) Maintaining the LCD Display Case. Clean with a soft cloth after disconnecting the power cord. Troubleshooting · · Do not use benzene, thinner or other flammable substances, or a wet cloth. We recommend that a ALTEC LANSING cleansing agent is used to prevent damage to the screen. 2) Maintaining the Flat Panel Display Screen. Clean with a soft cloth (cotton flannel) smoothly. · Never use acetone, benzene or thinner. (They may cause flaws or deformation of the screen surface. ) · The user will be required to pay costs and related expenses for repairing damages caused. Symptoms and Recommended Actions Note A LCD Display recreates visual signals received from the computer. Therefore, if there is a problem with the computer or the video card, this can cause the LCD Display to become blank, have poor coloring, become noisy, etc. In this case, first check the source of the problem, and then contact a Service Center or your dealer. Check if the power cord and the video cables are properly connected to the computer. [. . . ] (Refer to the Connecting a Computer) A: Q: A: A: Q: A: Check the volume level. If the volume is still too low after turning the control to its maximum, check the volume control on the computer sound card or software program. Adjusts the Treble and Bass to the appropriate levels. Problems related to the Remote Control Note Problems related to the remote control and their solutions are listed. Q: A: The remote control buttons do not respond. [. . . ]