User manual AMERICAN DJ GALAXIAN 3D

[. . . ] Galaxian 3D General Introduction Unpacking: Thank you for purchasing the Galaxian 3DTM by American DJ®. Every Galaxian 3DTM has been thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping. If the carton appears to be damaged, carefully inspect your fixture for any damage and be sure all equipment necessary to operate the unit has arrived intact. [. . . ] Do not use the ground lug on the XLR connector. Do not connect the cable's shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR's outer casing. Grounding the shield could cause a short circuit and erratic behavior. 3-Pin XLR to 5-Pin XLR Conversion Conductor Ground/Shield Data Compliment (- signal) Termination reduces signal errors and Data True (+ avoids signal transmission problems signal) and interference. It is always advisable to connect a DMX terminal, (Resistance 120 Ohm 1/4 W) between PIN 2Not Used (DMX-) and PIN 3 (DMX +) of the last fixture. 3-Pin XLR Female (Out) Pin 1 Pin 2 Pin 3 5-Pin XLR Male (In) Pin 1 Pin 2 Pin 3 Pin 4 - Do Not Use Pin 5 - Do Not Use COMMON DMX512 OUT 3-PIN XLR 1 2 3 DMX + DMX - 3 1 2 DMX512 IN 3-PIN XLR 3 1 2 Figure 2 Not Used XLR Male Socket 1 Ground SOUND REMOTE CONTROL INPUT XLR Female Socket 2 Cold SOUND XLR Pin Configuration Pin 1 = Ground INPUT Pin 2 = Data Compliment (negative) REMOTE CONTROL INPUT OUTPUT 2 Cold INPUT OUTPUT 1 Ground 3 Hot 3 Hot Pin 3 = Data True (positive) Figure 3 Special Note: Line Termination. When longer runs of cable are POWER POWER used, you may need to use a terminator on the last unit to avoid erratic behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is connected between pins 2 and 3 of a male XLR connector (DATA + and DATA -). This unit is inserted in the female XLR connector of the last unit in your daisy chain to terminate the line. Using a cable terminator (ADJ part number Z-DMX/T) will decrease the possibilities of erratic behavior. 3 1 2 DMX512 IN 3-PIN XLR 3 1 2 Termination reduces signal errors and avoids signal transmission problems and interference. It is always advisable to connect a DMX terminal, (Resistance 120 Ohm 1/4 W) between PIN 2 (DMX-) and PIN 3 (DMX +) of the last fixture. Figure 4 ©American DJ® - www. americandj. com - Galaxian 3D Instruction Manual Page 7 ©American DJ® - www. americandj. com - Galaxian 3D Instruction Manual Page 8 Galaxian 3DTM System Menu Chart Galaxian 3DTM System Menu System Menu: When making adjustments you can press ENTER to confirm your setup or you can wait 8 seconds for automatic setup. To exit without making any adjustments press the MENU button. ADDR - DMX Address Setting. 1. Tap the either the MENU, UP, or DOWN buttons until "ADDR" is displayed, press ENTER. The current address will now be displayed and flashing. Press the UP or DOWN buttons to find your desired address. Press ENTER to set your desired DMX address. SLND - This will let you set unit as a master or slave in a master/slave configuration. Tap the MENU button until "SLND" is displayed, press ENTER. Either "SL 1" or "SL 2" will be displayed. Tap the MENU button until "TEST" is displayed, press ENTER. The unit will now run a self-test program FHRS - With this function you can display the running time of the fixture. Tap the MENU button until "FHRS" is displayed, press ENTER. ©American DJ® - www. americandj. com - Galaxian 3D Instruction Manual Page 11 ©American DJ® - www. americandj. com - Galaxian 3D Instruction Manual Page 12 Galaxian 3DTM Operation Galaxian 3DTM Operation operating Modes: The Galaxian 3DTM can operate in two different modes. In each mode you can run the fixture as a stand alone fixture or in a master/slave confiugration. This next section will detail the differences in the operating modes. · Sound Active mode The fixture will react to sound, chasing through the built-in programs. · DMX control mode This function will allow you to control each individual fixtures traits with a standard DMX-512 controller such as the Elation® Show Designer. TM 3. [. . . ] If any accessories are shipped with the product, American DJ, Inc. shall have no liability whatsoever for loss of or damage to any such accessories, nor for the safe return thereof. This warranty is void if the serial number has been altered or removed; if the product is modified in any manner which American DJ, Inc. concludes, after inspection, affects the reliability of the product; if the product has been repaired or serviced by anyone other than the American DJ, Inc. [. . . ]