User manual AMERICAN DJ REVO RAVE

[. . . ] Revo RaveTM Introduction Unpacking: Thank you for purchasing the Revo RaveTM by American DJ®. Every Revo RaveTM has been thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping. If the carton appears to be damaged, carefully inspect your fixture for any damage and be sure all accessories necessary to operate the unit has arrived intact. [. . . ] When inserting standard 5-pin XLR connectors in to a 3-pin line a cable adaptor must be used, these adaptors are readily available at most electric stores. The chart below details a proper cable conversion. 3-Pin XLR to 5-Pin XLR Conversion Conductor Ground/Shield Data Compliment (- signal) Data True (+ signal) Not Used Not Used 3-Pin XLR Female (Out) Pin 1 Pin 2 Pin 3 5-Pin XLR Male (In) Pin 1 Pin 2 Pin 3 Do Not Use Do Not Use ©American DJ Supply® - www. americandj. com - Revo RaveTM User Manual Page 6 Revo RaveTM System Menu Revo RaveTM System Menu System Menu: When making adjustments you can press ENTER to confirm your setup or you can wait 8 seconds for automatic setup. To exit without making any adjustments press the MENU button. ADDR - DMX Address Setting. 1. Tap the either the MENU, UP, or DOWN buttons until "ADDR" is displayed, press ENTER. The current address will now be displayed and flashing. Press the UP or DOWN buttons to find your desired address. Press ENTER to set your desired DMX address. SLND - This will let you set unit as a master or slave in a master/slave configuration. Tap the MENU button until "SLND" is displayed, press ENTER. Either "MAST", "SL 1" or "SL 2" will be displayed. Tap the UP or DOWN buttons until your desired setting is displayed, press ENTER to confim. NoTE: In a Master/Slave configuration you can set one fixture to Master and then set the next fixture to "SL 2", the fixtures will now have contrast movement to each other. SHND: SH 0 - 12 - Show modes 0-12 (Factory programs). For show mode to run properly, make sure sound active mode is off. Tap the MENU button until "SHND" is displayed, press ENTER. 2. "Sh X" will now be displayed, "X" representing a number between 0-10. Programs 1-12 are factory programs, while "Sh 0" is random mode. Press the UP or DOWN buttons to find your desired show and press the ENTER, then press and hold the MENU button for at least 3 seconds to confirm. ©American DJ Supply® - www. americandj. com - Revo RaveTM User Manual Page 7 ©American DJ Supply® - www. americandj. com - Revo RaveTM User Manual Page 8 Revo RaveTM System Menu Revo RaveTM System Menu SOUN - Sound Active mode. 1. Tap the MENU button until "SOUN" is displayed, press ENTER. The display will show either "ON" or "OFF". Press the UP or DOWN buttons to select "ON" to activate sound active mode, or "OFF" to deactivate sound active mode. Press the ENTER, and then press and hold the MENU button for at least 3 seconds to confirm. for at least 3 seconds to confirm. TEST - This function will run a self test program. 1. Tap the MENU button until "TEST" is displayed, press ENTER. The fixture will now run a self test. FHRS - With this function you can display the running time of the fixture. [. . . ] If any accessories are shipped with the product, American DJ, Inc. shall have no liability whatsoever for loss of or damage to any such accessories, nor for the safe return thereof. This warranty is void if the serial number has been altered or removed; if the product is modified in any manner which American DJ, Inc. concludes, after inspection, affects the reliability of the product; if the product has been repaired or serviced by anyone other than the American DJ, Inc. [. . . ]