User manual AMX 10.4 TOUCH PANELS (G3 FIRMWARE)

[. . . ] instruction manual 10. 4" Touch Panels (Firmware version G3) Tou c h Pa n els an d A cc e ss o r ie s AMX Limited Warranty and Disclaimer AMX Corporation warrants its products to be free of defects in material and workmanship under normal use for three (3) years from the date of purchase from AMX Corporation, with the following exceptions: · · · Electroluminescent and LCD Control Panels are warranted for three (3) years, except for the display and touch overlay components that are warranted for a period of one (1) year. Disk drive mechanisms, pan/tilt heads, power supplies, and MX Series products are warranted for a period of one (1) year. AMX Lighting products are guaranteed to switch on and off any load that is properly connected to our lighting products, as long as the AMX Lighting products are under warranty. AMX Corporation does guarantee the control of dimmable loads that are properly connected to our lighting products. [. . . ] ADBEEP Syntax: Outputs a double "'ADBEEP'" beep even if the Example: double beep value SEND_COMMAND TP, "'ADBEEP'" is set to 0 in the Setup page. AKEYB Opens the touch panel keyboard and initializes the text string entry. The keyboard string is set to null during power-up and stored until power-down. Syntax: "'AKEYB-<text string>'" Variable: text string = 0 - 59 characters Example: SEND_COMMAND TP, "'AKEYB-TOUCH HERE'" Opens the touch panel keyboard with TOUCH HERE in the display. AKEYP Opens the touch panel keypad and initializes the number string entry. The keyboard string is set to null during power-up and stored until power-down. Syntax: "'AKEYP-<number string>'" Variable: number string = 0 - 9999 Example: SEND_COMMAND TP, "'AKEYP-1988'" Opens the touch panel keypad with 1988 in the display. AKEYR Closes/opens the touch panel keyboard/pad. Syntax: "'AKEYR'" Example: SEND_COMMAND TP, "'AKEYR'" Closes the keyboard/keypad opened using the 'AKEYB', 'AKEYP', or 'PKEYP' commands. 28 10. 4" Touch Panels Programming System Send_Commands (Cont. ) BAUD Sets the program port baud rate. The baud rate can also be set in the Protected Setup page's BAUD level indicator. Syntax: "'BAUD <baud rate>'" Variable: baud rate = 38400, 19200, 9600, 4800, 2400, 1200, 600, and 300 Example: SEND_COMMAND TP, "'BAUD 38400'" Sets the Baud rate to 38400. BEEP This beep command sounds one tone for a time length of 50 milliseconds. "'BEEP'" Example: SEND_COMMAND TP, "'BEEP'" Activates one beep tone. Beeps the panel if the Beep button is not set to 0. The BEEP command does not disable the beep after a QBEEP command. BRIT Syntax: Adjusts brightness "'BRIT-<level>'" of display. Variable: level = 1 - 8 (1 = minimum; 8 = maximum) Example: SEND_COMMAND TP, "'BRIT-8'" Sets to highest brightness level. CALIBRATE Starts the touch panel calibration sequence. Syntax: "'CALIBRATE'" Example: SEND_COMMAND TP, "'CALIBRATE'" Starts the calibration operation on the touch panel. Syntax: "'CLOCK <mm-dd-yy> <hh:mm:ss>'" Variables: mm = 01 - 12, dd = 01 - 31, yy = 00 - 99 hh = 00 - 23, mm = 00 - 59, ss = 00 - 59 Example: SEND_COMMAND TP, "'CLOCK 02-08-98 19:16:00'" Sets the touch panel's date to February 8, 1998, and time to 7:16 p. m. CURSOR Syntax: Turns the cursor "'CURSOR <OFF/ON>'" display On or Off if Variables: the touch device Off = 0 and On = 1 has a cursor. Example: SEND_COMMAND TP, "'CURSOR 0'" Turns the cursor display Off. 10. 4" Touch Panels 29 Programming System Send_Commands (Cont. ) DBEEP Gives a double beep output. [. . . ] The batteries are not used when DC power is supplied to the touch panel. Write down the replacement date on a label by adding 2. 5 years to the date of installation, and attach it to the panel for future reference. FIG. 22 Lithium battery and socket Static electricity can damage electronic circuitry. Before removing the touch panel circuit card from the enclosure, discharge any accumulated static electricity from your body and flat-blade tool by touching a grounded metal object. Before replacing the lithium batteries, make sure you have a current copy of the pages stored in the touch panel. [. . . ]