User manual AMX AXB-PT15 POSITRACK CAMERA CONTROLLER

[. . . ] instruction manual AXB-PT15 PosiTrack Camera Controller C a m e ra C o n t r o l l e r s AMX Limited Warranty and Disclaimer AMX Corporation warrants its products to be free of defects in material and workmanship under normal use for three (3) years from the date of purchase from AMX Corporation, with the following exceptions: · · · Electroluminescent and LCD Control Panels are warranted for three (3) years, except for the display and touch overlay components that are warranted for a period of one (1) year. Disk drive mechanisms, pan/tilt heads, power supplies, and MX Series products are warranted for a period of one (1) year. AMX Lighting products are guaranteed to switch on and off any load that is properly connected to our lighting products, as long as the AMX Lighting products are under warranty. AMX Corporation does guarantee the control of dimmable loads that are properly connected to our lighting products. [. . . ] Syntax: SEND_COMMAND CAM, "'CHAN PRESET=ON'" The default mode of operation for these channels is feedback ONLY. Syntax: SEND_COMMAND CAM, "'CHAN PRESET=OFF'" Syntax: SEND_COMMAND CAM, "'CLEAR ERRORS'" Refer to the Diagnostic error values section on page 39 for detailed information. 26 AXB-PT15 PosiTrack Camera Controller Programming Configuration Commands (Cont. ) CLEAR HOME Clears the current home position and goes to the default setting and clears presets. CLEAR LIMIT ALL Clears all of the limits. CLEAR LIMIT DOWN Clears the tilt-down limit. CLEAR LIMIT LEFT Clears the pan-left limit. CLEAR LIMIT RIGHT Clears the pan-right limit. CLEAR LIMIT UP Clears the tilt-up limit. CURRENT SPEED PRIORITY=CHANNEL Changes the operational mode of channels 31, 32, 35, and 36. CURRENT SPEED PRIORITY=LEVEL Syntax: SEND_COMMAND CAM, "'CLEAR HOME'" This command also clears all presets. Syntax: SEND_COMMAND CAM, "'CLEAR LIMIT ALL'" Syntax: SEND_COMMAND CAM, "'CLEAR LIMIT DOWN'" Syntax: SEND_COMMAND CAM, "'CLEAR LIMIT LEFT'" Syntax: SEND_COMMAND CAM, "'CLEAR LIMIT RIGHT'" Syntax: SEND_COMMAND CAM, "'CLEAR LIMIT UP'" Syntax: SEND_COMMAND CAM, "'CURRENT SPEED PRORITY=CHANNEL'" Does NOT allow pan/tilt movement from levels until channels 31, 32, 35 and 36 are turned Off. Setting this priority puts the unit in CaMatrix compatible mode. The CaMatrix is a third-party RS232 control program that runs on a PC. Syntax: SEND_COMMAND CAM, "'CURRENT SPEED PRORITY=LEVEL'" Changes the operaAllows pan/tilt movement from levels even if these channels are still On. tional mode of channels Setting this priority makes the move at current speed channels operate like the 31, 32, 35, and 36. DEFAULT ACCEL Sets the Pan and Tilt acceleration to the default value of 90 degrees/(second squared). FIND HOME Syntax: SEND_COMMAND CAM, "'DEFAULT ACCEL'" Syntax: Runs a series of pan/tilt SEND_COMMAND CAM, "'FIND HOME'" movements to After the mechanical recalibration, the unit moves to the location set via the recalibrate its "SET HOME" command (if applicable). FOCUS PRESET=POS This is applicable only if the FOCUS SIGNAL=S command is in effect, and the FOCUS switch is set to the S position (servomotor mode). Sets the FOCUS voltage output to recall positional presets (default). Syntax: SEND_COMMAND CAM, "'FOCUS PRESET=POS'" The command for FOCUS output to servomotor mode or motor mode MUST be configured to match the switch settings. AXB-PT15 PosiTrack Camera Controller 27 Programming Configuration Commands (Cont. ) FOCUS PRESET=SPEED Sets the FOCUS voltage output to recall speed presets. This is applicable only if the FOCUS SIGNAL=S command is in effect, and the FOCUS switch is set to the S position (servomotor mode). Syntax: SEND_COMMAND CAM, "'FOCUS PRESET=SPEED'" The command for FOCUS output to servomotor mode or motor mode MUST be configured to match the switch settings. FOCUS SIGNAL=M This setting corresponds to the M position (motor mode) setting on the FOCUS Sets the FOCUS output switch. Syntax: SEND_COMMAND CAM, "'FOCUS SIGNAL=M'" The command for FOCUS signal must be configured to match the switch settings. FOCUS SIGNAL=S Sets the Focus output to be a servomotor output. This setting corresponds to the FOCUS switch in the S position. [. . . ] If power is lost between the erase of flash memory and the completion of copying the new boot code from RAM to flash memory, the unit will not operate at all when power returns. If you have not already installed the SOFTROM program, do so by following the steps contained on the AMX Control Disc. Configuration To configure the communication setting for the SOFTROM program: 1. Press F1, the Configuration screen appears. [. . . ]