User manual AMX AXB-SPE SERVER PORT EXPANDER

[. . . ] instruction manual AXB-MPE+ Master Port Expander AXB-SPE Slave Port Expander A x c e s s C e n t ra l C o n t r o l l e r s a n d C a r d s AMX Limited Warranty and Disclaimer AMX Corporation warrants its products to be free of defects in material and workmanship under normal use for three (3) years from the date of purchase from AMX Corporation, with the following exceptions: · · · · · Electroluminescent and LCD Control Panels are warranted for three (3) years, except for the display and touch overlay components that are warranted for a period of one (1) year. Disk drive mechanisms, pan/tilt heads, power supplies, MX Series products, and KC Series products are warranted for a period of one (1) year. Unless otherwise specified, OEM and custom products are warranted for a period of one (1) year. Software is warranted for a period of ninety (90) days. [. . . ] Two-pin (male) connector that supplies 12VDC to the AXB-SPE. The power is distributed in parallel to each AXlink connector. The total load for all AXlink connectors must not exceed 4 amps. 12 four-terminal connectors for captive wire compression Two 4-pin modular telco connectors · 11. 8 to 16V DC, 150mA (maximum draw) · 2-pin connector for captive wire compression · 1. 72" x 19. 00"(with rack ears) x 12. 09" (4. 37 cm x 48. 26 cm x 30. 71 cm) · One standard rack unit high. ! 1 stop bit 8 data bits No parity 38. 4K baud To reset the DIP switch to its default settings, place all switches in the ON position. 6 AXB-MPE+ Master Port Expander and AXB-SPE Slave Port Expander Installation and Configuration Configuring the MPE+ to use One or Two AXC-EM Cards The AXB-MPE+ Master Port Expander uses one AXC-EM master card. The AXB-MPE+ Dual Master Port Expander uses two AXC-EM master cards. Both come factory set to either a single or dual expander. If you are using an AXC-MPE+ Master Port Expander and want to upgrade the unit to use two AXC-EMs: 1. Discharge the static electricity from your body by touching a grounded object. Remove the two Phillips-head screws from the top panel on the AXB-MPE+, and slide the panel backward to access the AXC-EM Master Cards (FIG. Locate the Jumper location (JP1A and JP1B) between the AXC-EM internal connection ports. AXC-EM Card #2 AXC-EM Card #1 Dual/Single Master Expander jumpers (JP1A and JP1B) JP1B jumper JP1A jumper FIG. 3 MPE+ internal locations for AXC-EM cards and respective jumpers 4. To set the Port Expander to use one master, place the jumper from JP1A on pins 1 and 2 (SINGLE) and verify that the jumper from JP1B is also on pins 1 and 2. This setting allows the user to program the single AXC-EM card using either the front or rear Program ports. Refer to the Programming the AXB-MPE+ (One AXC-EM Card) section on page 11 for more information. To set the Port Expander to use two master, place the jumper from JP1A on pins 2 and 3 (DUAL) and verify that the jumper from JP1B is also on pins 2 and 3. Refer to the Programming the AXB-MPE+ Dual Master Port Expander (Two AXC-EM Cards) section on page 12 for more information. This setting allows the user to ONLY program: !3) using the front Program port on the MPE+ and AXC-EM Card #2 (see FIG. 3) using the rear Program port on the MPE+. AXB-MPE+ Master Port Expander and AXB-SPE Slave Port Expander 7 Installation and Configuration Wiring the AXB-MPE+ and AXB-SPE You must connect a 12 VDC power supply to the AXB-MPE+ and AXB-SPE to control external equipment. If you connect external AMX equipment, refer to the associated AMX manuals for wiring and power supply information. This section describes how to wire a control system. [. . . ] Close the top panel, insert the Phillips-head screws, and tighten. Return the AXB-EM+ to the equipment rack and reconnect all the connectors removed in step 2. Installing the AXB-MPE+, AXB-SPE, and External Equipment Install the AXB-MPE+ into a standard 19-inch rack using the supplied rack kit: 1. Mount the AXB-MPE+ and AXB-SPE in the equipment rack. Mount the external AMX equipment where it will be used. AXCESS Programming You can program the AXC-EM Master Cards in the AXB-MPE+ with an AXCESS software program to control a wide variety of audiovisual, lighting, and audio equipment. [. . . ]