User manual AMX AXB-TM5 TELEVISION MANAGER

[. . . ] instruction manual AXB-TM5 Television Manager AXlink Bus Controllers AMX Limited Warranty and Disclaimer AMX Corporation warrants its products to be free of defects in material and workmanship under normal use for three (3) years from the date of purchase from AMX Corporation, with the following exceptions: · · · · · Electroluminescent and LCD Control Panels are warranted for three (3) years, except for the display and touch overlay components that are warranted for a period of one (1) year. Disk drive mechanisms, pan/tilt heads, power supplies, MX Series products, and KC Series products are warranted for a period of one (1) year. Unless otherwise specified, OEM and custom products are warranted for a period of one (1) year. Software is warranted for a period of ninety (90) days. [. . . ] Wiring Guidelines The AXB-TM5 requires 12 VDC power to operate properly. The power can be supplied by the AMX system's AXlink cable or with an optional 12 VDC power supply. The maximum wiring distance between the control system and AXB-TM5 is determined by power consumption, supplied voltage, and the wire gauge used for the cable. The following table lists wire sizes and the maximum lengths allowable between the AXB-TM5 and the control system. The maximum wiring lengths are based on a minimum of 13. 5 volts available at the control system's power supply. Wiring Guidelines @ 200 mA Wire size 18 AWG 20 AWG 22 AWG 24 AWG Maximum wiring length 586. 55 feet (178. 78 meters) 371. 29 feet (113. 17 meters) 231. 48 feet (70. 56 meters) 145. 91 feet (44. 47 meters) If the AXB-TM5 is installed farther away from the control system than recommended in the above table, connect an external 12 VDC power supply to the two-pin PWR connector on the rear panel. Using the AXlink connector for data and power To use the AXlink 4-pin connector for data communication and for power supply, the incoming PWR and GND cable from the control system must be connected to the AXlink cable connector going to the control system as sown in the AXlink wiring diagram (FIG. 3). PWR + AXP/TX AXM/RX GND To the AXB-TM5 FIG. 3 AXlink connector wiring diagram PWR + AXP/TX AXM/RX GND To the Control system 4 AXB-TM5 Television Manager Connection and Wiring CC-IRC emitter wiring connections FIG. 4 shows how to connect a CC-IRC IR Emitter to the IR Emitter connector on the AXB-TM5. CC-IRC To emitter GND connector SIG Television FIG. 4 CC-IRC Emitter wiring connections IR emitter to device installation The following steps describe the installation of the IR emitter to the television IR window. Using a sharp edged tool (knife blade, razor knife, etc. ), separate the factory-installed shell as shown in FIG. 5 Removing factory-installed shell 2. If necessary, use scissors and trim the shield to fit. FIG. Remove the adhesive back covering from the IR shield and place the IR emitter diode into the mirrored recessed area (FIG. 7) of the shield. IR input window IR shield IR emitter code CC-IRC cable assembly FIG. 7 IR emitter diode installed AXB-TM5 Television Manager 5 Connection and Wiring For additional information concerning the IR emitter, refer to the IR Sensors and Receivers instruction manual. 4. 11 IRX-SM connections GND OUT AUX OUT +12 VDC IRX-SM #1 This configuration is for 40 kHz operation only. AXB-TM5 Television Manager 7 Connection and Wiring 8 AXB-TM5 Television Manager Programming Programming You can program the AXB-TM5 to perform a wide variety of operations using Axcess Send_Commands. This section describes channel settings, IR functions, and system Send_Commands. Refer to the AXCESS Programming Guide for additional programming information. Channel Setting Commands The AXB-TM5 use the channel setting commands listed in the following table. AXB-TM5 Channel Settings Channel 1 2 - 127 128 - 247 248 249 250 251 252 253 254 255 Function Generates IR/Serial functions 1, else Off Channels the generate IR code for the corresponding functions Push and release channels for received IR code A push on this channel indicates a power failure error Response LED blinks when channels 249 and 250 are On Response LED lights when channel is On I/O is On (switch to GND) when channel is On I/O 2 is On (switch to GND) when channel is On I/O 3 is On (switch to GND) when channel is On I/O 4 is On (switch to GND) when channel is On Channel is On if the TV Power Sensor detects a horizontal scan frequency Turning a channel (IR/Serial function) on while another one is currently on will automatically turn the current one off first. Contact closure inputs on I/O 1 through I/O 4 will also generate PUSHes and RELEASEs on channels 251 through 254, respectively. Device Assignment The device assignment must be the same as the device number set on the Device DIP switches (FIG. [. . . ] Example: SEND_COMMAND AXBTMX, '?PTOF' Sends the current IR power pulse off time from the AXB-TM5 to the control system in the 'PTOF <Time>' format. 'PTON', <Time> Sets the IR power pulse on time in increments of . 10 seconds. Syntax: "'PTON', <Time>" Variables: Time = 0 through 255 System default is 5 (. 5 second). 'PTON' sets the pulse length for all power pulses, regardless if the pulse is due to a 'PON' or 'POF' command. [. . . ]