User manual AMX AXC-TEMP AND RTS-1 TEMPERATURE CONTROL CARD AND ROOM TEMPERATURE SENSOR

[. . . ] This limitation of liability applies whether damages are sought, or a claim is made, under this warranty or as a tort claim (including negligence and strict product liability), a contract claim, or any other claim. This limitation of liability cannot be waived or amended by any person. This limitation of liability will be effective even if AMX Corporation or an authorized representative of AMX Corporation has been advised of the possibility of any such damages. This limitation of liability, however, will not apply to claims for personal injury. [. . . ] 2 RTS1 Features The AXC-TEMP features include: !! Standard Axcess CardFrame slot size Settings for Fahrenheit or Celsius operation Control and power for up to four independent RTS1 units Measurement accuracy of +/- 2°F (+/- 1. 1°C) Calibration for zero temperature deviation The RTS1 features include: !! Precise temperature measurement from 5× to 128°F (-29. 2× to +106. 9°C) Connection to the AXC-TEMP card with a shielded 3-conductor cable AXC-TEMP Temperature Control Card and RTS1 Room Temperature Sensor 1 Product Information The table below lists the specifications for the AXC-TEMP and RTS1. Specifications AXC-TEMP Input voltage Current Draw Temperature range Accuracy Resolution +12 to 18 VDC 40 mA (using four RTS1s = 75 mA) 0. 0 ° F to +250 ° F (0. 0 ° C to +106. 9 ° C) +/-2 ° F (+/-1. 1 ° C) 10-bit (1024 steps over range) RTS1 Weight Dimensions Enclosure Resolution Temperature range 3. 2 oz. (91 grams) 4. 5" x 2. 75" x 9" (114 mm x 70 mm x 23 mm) Metal, off-white finish 10-bit (1024 steps over range) -20. 5°F to +250°F (-29. 2°C to 106. 9°C) 2 AXC-TEMP Temperature Control Card and RTS1 Room Temperature Sensor Pre-Installation Pre-Installation Before installing the AXT-TEMP and RTS1, you must properly set jumpers and potentiometers (POTs). Setting Fahrenheit or Celsius Set the Fahrenheit or Celsius feature by manually selecting each jumper (JP1- JP4) or by manually selecting the RAW A/D OUTPUT jumper on the card. 3 shows the location of the jumpers and POTs. The RAW A/D OUTPUT jumper overrides jumpers JP1 - JP4. Channels 1 - 4 Jumpers JP5 - JP8 Jumpers JP1 - JP4 and JP13 (RAW) FIG. 3 Location of jumpers and POTs Jumpers JP9 - JP12 Setting the Jumpers Use the two-position jumpers (FIG. 4) to select Fahrenheit or Celsius operation. The setting takes effect when you power on the system or reinsert the card into the CardFrame. The default setting is Fahrenheit (°F). °F °C JP1 FIG. Set each jumper (JP1 - JP4) on the card for either Fahrenheit or Celsius. Full counter-clockwise is a -4° variance and full clockwise is a +4° variance. To access the jumper and POTs, remove the AXC-TEMP card from the CardFrame. After making all adjustments, be sure to reseat the card properly. You can also adjust the card using an optional Axcess Extender Card (AXC-EXTN), for easier access. 3. Insert the card into the desired Axcess CardFrame slot. It is not necessary to disconnect power to the CardFrame when installing the card. AXC-TEMP Temperature Control Card and RTS1 Room Temperature Sensor 3 Pre-Installation 4. Hold the card by the tab end and slide the card into the frame. Make sure the card is correctly positioned in the guide slot. Gently push the card in until it is firmly seated in the card connector slot. It is not necessary to disconnect the power to the CardFrame when installing the card. Calibrating POTs Use the four calibration potentiometers (POTs), marked CH 1 - CH 4, to adjust the respective RTS1 units 1 - 4. The default setting for each POT pointer is 0°. [. . . ] Allow the reference thermometer to stabilize approximately one minute, then check. If necessary, repeat steps 1 - 5 for RTS1 units 2 - 4, and move the reference thermometer near each sensor you are calibrating. 6 AXC-TEMP Temperature Control Card and RTS1 Room Temperature Sensor Pre-Installation Testing the RTS1 Touch the sensor at the bottom each RTS1 unit for a few seconds. The temperature on the display panel should change. Check the wiring to each RTS1 unit that did not display a temperature change. [. . . ]