User manual AMX I!-PCLINK WEB

[. . . ] instruction manual i!-PCLink/Web i n t e g ra t i o n !S o l u t i o n s AMX Limited Warranty and Disclaimer AMX Corporation warrants its products to be free of defects in material and workmanship under normal use for three (3) years from the date of purchase from AMX Corporation, with the following exceptions: · · · Electroluminescent and LCD Control Panels are warranted for three (3) years, except for the display and touch overlay components that are warranted for a period of one (1) year. Disk drive mechanisms, pan/tilt heads, power supplies, and MX Series products are warranted for a period of one (1) year. AMX Lighting products are guaranteed to switch on and off any load that is properly connected to our lighting products, as long as the AMX Lighting products are under warranty. [. . . ] You should take a few moments to familiarize yourself with the basic elements listed below: FIG. 5 Control Panel i!-PCLinkWeb 5 Running i!-PCLink/Web NetLinx Connection To configure the NetLinx connection settings, please select the Configure button on the main page. (Note, the Configure button is not available if there is an active connection, you must first disconnect. ) You will be prompted with a connection configuration dialog. Completely fill out all remaining connection setting information pertaining to the particular connection method you selected. i!-PCLink/Web supports the following NetLinx connection methods: a. 6 TCP/IP Connect (Network) In the Connect mode, the i!-PCLink/Web application actively connects to the NetLinx master. You simply need to enter the IP Address or Host Name of the NetLinx master in the "Host Address" box and enter the ICSP port number in the "Host Port" box. If you have not changed the ICSP port of the master through telnet or terminal, it is using the default of 1319). This is the recommended connection method. 6 i!-PCLinkWeb Running i!-PCLink/Web b. 7 TCP/IP Listen (Network) In the Listen mode, the i!-PCLink/Web application waits for a NetLinx master to attempt the connection. Enter the ICSP port number in the "Host Port" box. If you have not changed the ICSP port of the master through telnet or terminal, it is using the default of 1319. The Host Name or IP address of the Host computer must be entered in the URL List of the NetLinx master for Listen mode. i!-PCLinkWeb 7 Running i!-PCLink/Web You must add the IP address of the i!-PCLink/Web PC to the URL list of the NetLinx master (using NetLinx Studio). Establish a vaild connection to a master via NetLinx Studio. Select the OnLine Tree tab from the Workspace window. Select Diagnostics > URL Listing from the Main menu (FIG. 8). System Address reflects the value set in the Device Addressing tab Used to obtain an existing URL List from Master Used to set the URL List on Master FIG. Enter the System and Device number for the specific Master associated with your PC (as seen in the Online Tree tab). Click Add and enter the IP Address of the PC into the Add URL dialog box. Click OK to enter your IP Address and add it to the list. Click Done once you are finished adding your panel information to the list. Press the on-screen Reboot button to save any changes and restart the panel. 8 i!-PCLinkWeb Running i!-PCLink/Web c. 9 Serial (RS232) Please enter the COM port communications settings of the NetLinx master with i!-PCLink/Web installed. [. . . ] Returns the current URL from the internal web browser. i!-PCLinkWeb 21 Programming i!-PCLink/Web In-bound Strings (Cont. ) BROWSERTITLE-<title> BROWSERSTATUS-<status> LINKCOUNT-<count> LINK-<index>, <name> LINKURL-<index>, <url> WINDOWCOUNT-<count> WINDOW-<index>, <handle>, <name> Returns the current webpage title from the internal web browser. Returns the current browser status/link from the internal web browser. Received the internal web browser link count Received an internal web browser link list item Received a internal web browser link item url Returns the total number of windows on the computer. Returns a window list item. Out-bound Strings i!-PCLink/Web also supports a file directly as an out-bound strings (master to device). [. . . ]