User manual AMX MVP-TDS TABLETOP DOCKING STATION

[. . . ] Operation/Reference Guide MVP-TDS Table Docking Station for MVP-7500/8400 Modero® ViewPoint® Wireless Touch Panels Touch Panels & Accessories Last Revised: 10/06/2006 AMX Limited Warranty and Disclaimer AMX warrants its products to be free of defects in material and workmanship under normal use for three (3) years from the date of purchase from AMX, with the following exceptions: · · · Electroluminescent and LCD Control Panels are warranted for three (3) years, except for the display and touch overlay components that are warranted for a period of one (1) year. Disk drive mechanisms, pan/tilt heads, power supplies, and MX Series products are warranted for a period of one (1) year. AMX Lighting products are guaranteed to switch on and off any load that is properly connected to our lighting products, as long as the AMX Lighting products are under warranty. AMX does guarantee the control of dimmable loads that are properly connected to our lighting products. [. . . ] The following table lists the specifications for the MVP-TDS Table Top Docking Station. Specifications MVP-TDS Specifications Dimensions (HWD): Power Requirements: · Fully raised: 7. 49" x 7. 00" x 9. 83" (19. 02 cm x 17. 78 cm x 25. 00 cm) · Fully lowered: 4. 27" x 7. 00" x 9. 83" (10. 80 cm x 17. 78 cm x 25. 00 cm) · Stand-alone with no batteries: 0. 1 A @ 12 VDC · Stand-alone charging two batteries: 2. 1 A @ 12 VDC · With no batteries and charging a connected MVP panel's two internal batteries: 3. 3 A @ 12 VDC · With two batteries and charging a connected MVP panel's two internal batteries: 3. 3 A @ 12 VDC MVP-TDS Table Docking Station for MVP Panels 1 MVP-TDS Table Top Docking Station MVP-TDS Specifications (Cont. ) Weight: Charging Features: Front Panel Components: · Stand-alone: 3. 38 lbs (1. 53 kg) · With two batteries: 4. 18 lbs (1. 90 kg) · Two-Bays: Simultaneous Charging · Charge time for two depleted batteries ~ 5 hours · Electromagnet · MVP Interface Connector Pins: Provides both communication and power between the MVP and the MVP-TDS. · MVP Support Cradle: This cradle supports a MVP panel and allows a user to angle the MVP LCD. · LEDs (blue): - Left LED indicates battery status in either the MVP-TDS or MVP - Right LED indicates communication between the MVP-TDS and MVP · Security Release pushbutton: Toggles an on-screen keypad for entering a security code (password). If security is enabled, a valid password must be entered before the MVP can be removed from the TDS. Rear Panel Components: · Battery Compartment: Houses up to two MVP-BP batteries. · USB Connectors: Two type A USB ports connect an external keyboard and mouse device for use with the G4 Computer Control application. · Power Connector: 2. 1 mm barrel-style power jack - connects to a PS4. 4 power supply connector. Operating/Storage Environments: · Operating Temperature: 0° C (32° F) to 40° C (104° F) · Operating Humidity: 20% - 85% RH · Storage Temperature: -20° C (-4° F) to 60° C (140° F) · Storage Humidity: 5% - 85% RH MVP-TDS docking station connectors FIG. 2 shows the layout of the connectors on the rear of the MVP-TDS. Battery Compartment 1 Keyboard/Mouse USB Connectors Battery Compartment 2 12VDC KEYBOARD/ MOUSE KEYBOARD/ MOUSE PWR PWR connector (for use with PS4. 4 power supply) FIG. 2 Connector layout on the rear of the MVP-TDS 2 MVP-TDS Table Docking Station for MVP Panels MVP-TDS Table Top Docking Station MVP-TDS LED Indicators The two LED indicators indicate the battery and communication status: LED Pattern Indicators for the MVP-TDS LED TDS only Solid Bright Flashing Bright (Slow) Flashing Bright (Fast) Solid Dim Left - Battery Status MVP in Cradle MVP panel is docked and communicating N/A MVP panel is docked but not communicating MVP panel is NOT docked and NOT communicating TDS batteries are fully charged MVP batteries are fully charged TDS batteries are charging N/A TDS receiving power but contains no batteries in cradle MVP batteries are charging N/A No batteries within the MVP Right - Comm. Status Installation Interface Connector Pins and Functions FIG. 3 gives the pin numbering and function information for the docking stations 1 - Data - Panel Detect IN 2 - Ground 3 - not used 4 - Ground 5 - not used 6 - Ground 7 - not used 8 - not used 9 - not used 10 - DC Power 11 - Data - Receive 12 - DC Power 13 - Data - Transmit 14 - DC Power 15 - Data - USB Device D16 - Data - Cradle Detect 17 - Data - USB Device D+ 18 - Data - Panel Detect OUT FIG. 3 MVP-TDS Connector Pin locations and Pinout function 2 1 17 18 Connecting a Power Supply The MVP-TDS uses a PS4. 4 power supply (included with the MVP) to indirectly provide power to the MVP panel, while charging internal batteries. Static electricity can damage electronic circuitry. After the panel splash-screen disappears: If a USB mouse has been connected, a mouse cursor appears on the panel screen and its location corresponds to the mouse cursor position sent by the external USB mouse. If a USB keyboard has been connected, only on-screen keyboards and keypads will reflect any external keystrokes sent from the external USB keyboard. To be detected by the docking station, USB input devices (keyboard / mouse) must be plugged into the docking station before it is powered-up. The docking station will not detect USB input devices until the unit cycles power. 4 MVP-TDS Table Docking Station for MVP Panels MVP-TDS Table Top Docking Station Securing an MVP Panel to an MVP-TDS The MVP will not be able to communicate with or receive power from the MVP-TDS without a proper connection. 1. Place the MVP-TDS on a flat and level surface. Provide power to the MVP-TDS (refer to the Powering the MVP-TDS section on page 3). Place the MVP on the support cradle so that the alignment pins on the TDS fit into the matching holes on the bottom of the MVP. Once proper alignment is verified, gently angle back the MVP until the rear of the panel makes contact with the electromagnet. Allow one second to activate the electromagnet. When the MVP is properly docked, the following message is displayed on the panel (FIG. [. . . ] Right-click on the System entry and select Refresh System to re-populate the list. Verify the panel appears in the OnLine Tree tab of the Workspace window. The default Modero panel value is 10001. Locate the latest firmware file from the www. amx. com > Tech Center > Downloadable Files > Firmware Files > Modero Panels firmware (MVP Docking Stations: MVP-TDS/WDS) section of the website. [. . . ]