User manual AMX MVP-WDS WALL DOCKING STATION

[. . . ] Operation/Reference Guide MVP-WDS Wall Docking Station for MVP-7500/8400 Modero® ViewPoint® Wireless Touch Panels Touch Panels & Accessories Last Revised: 10/06/2006 AMX Limited Warranty and Disclaimer AMX warrants its products to be free of defects in material and workmanship under normal use for three (3) years from the date of purchase from AMX, with the following exceptions: · · · Electroluminescent and LCD Control Panels are warranted for three (3) years, except for the display and touch overlay components that are warranted for a period of one (1) year. Disk drive mechanisms, pan/tilt heads, power supplies, and MX Series products are warranted for a period of one (1) year. AMX Lighting products are guaranteed to switch on and off any load that is properly connected to our lighting products, as long as the AMX Lighting products are under warranty. AMX does guarantee the control of dimmable loads that are properly connected to our lighting products. [. . . ] Slide the Faceplate over the angled Support Cradle, toward the Security Release pushbutton's circuit board on the MVP-WDS (FIG. Gently press the faceplate down and under the Security Latch until it rests against the Mounting Tabs of the MVP-WDS main unit. Be sure to snap the Faceplate Connectors back into their respective Latches (located along the bottom rim of the faceplate - see FIG. Verify that the Security Release Pushbutton is properly aligned over it's LEDs and circuit board on the MVP-WDS main unit. Verify that the two faceplate security screw holes on both the Faceplate and the main MVP-WDS unit are properly aligned. 6. Insert and secure the two #6-32 Faceplate Security Screws into the top rim of the Faceplate using a grounded Phillips-head screwdriver. Apply power to the MVP-WDS by connecting the terminal end of the power cable to the power supply. Press the Cradle Activation pushbutton to cause the MVP Support Cradle to angle backwards and lie flush against the main unit. Remove the two adhesive plastic Die Cut Foam covers (60-5965-47) from the strip included within the Installation Kit bag. Adhere these two plastic Die Cut Foam covers into the two notches where the Faceplate Security Screws are located. Refer to the Securing an MVP Panel to an MVP-WDS section on page 15 and Removing an MVP Panel from an MVP-WDS section on page 16. Connecting a Power Supply The MVP-WDS Docking Station receives power from a 12-VDC compliant power supply using a 2-pin 3. 5 mm mini-Phoenix connector. Static electricity can damage electronic circuitry. Before touching the unit, discharge any accumulated static electricity from your body by touching a grounded metal object. Powering the MVP-WDS The MVP-WDS uses a 12-VDC compliant power supply (not included) to provide power to the MVP panel, while charging internal batteries. Once MVP batteries are fully charged, the MVP-WDS begins charging MVP-BP batteries inserted within its battery compartments. 1. Connect the terminal end of the power supply to the rear PWR connector on the WDS. Provide power to the MVP-WDS by connecting the AC power cord to an external power source. MVP-WDS Wall Docking Station for MVP Panels 13 MVP-WDS Wall Docking Station & CB-MVPWDS Conduit Box Initially, both blue LEDs illuminate and remain dim (indicating that the power is being supplied to the MVP-WDS). Using the 3. 5mm mini-Phoenix Connector for Power To use the 2-pin 3. 5 mm mini-Phoenix connector for use with a 12 VDC-compliant power supply, the incoming PWR and GND wires from the external source must be connected to their corresponding locations on the connector (FIG. 14) to provide power to the MVP-WDS. PWR + GND MVP-WDS FIG. 14 NetLinx power connector wiring diagram PWR + GND Power Supply Verify that the power supply is not receiving power. 1. Insert the PWR and GND wires on the terminal end of the 2-pin 3. 5 mm mini-Phoenix cable. Match the wiring locations of the +/- on both the power supply and the terminal connector. Tighten the clamp to secure the two wires. Do not overtighten the screws - doing so could damage the wires. Verify the connection of the 2-pin 3. 5 mm mini-Phoenix to the power supply, and apply power. Connecting and Using USB Input Devices on the Stations The MVP-WDS can have up to two USB input devices connected for use on the MVP panel's different firmware and TPD4 panel pages. These input devices can consist of a keyboard and mouse. USB-connected input devices are detected by the docking stations only after they are connected and then power is applied. 1. [. . . ] Right-click on the System entry and select Refresh System to re-populate the list. Verify the panel appears in the OnLine Tree tab of the Workspace window. The default Modero panel value is 10001. Locate the latest firmware file from the www. amx. com > Tech Center > Downloadable Files > Firmware Files > Modero Panels firmware (MVP Docking Stations: MVP-TDS/WDS) section of the website. [. . . ]