User manual AMX NETLINX CARDFRAME, CONTROL CARDS AND NETMODULES

[. . . ] instruction manual NetLinx CardFrame, Control Cards, and NetModules NXC, NXF, and NXM Series N e t L i n x C e n t ra l C o n t r o l l e r s a n d C a r d s AMX Limited Warranty and Disclaimer AMX Corporation warrants its products to be free of defects in material and workmanship under normal use for three (3) years from the date of purchase from AMX Corporation, with the following exceptions: · · · Electroluminescent and LCD Control Panels are warranted for three (3) years, except for the display and touch overlay components that are warranted for a period of one (1) year. Disk drive mechanisms, pan/tilt heads, power supplies, and MX Series products are warranted for a period of one (1) year. AMX Lighting products are guaranteed to switch on and off any load that is properly connected to our lighting products, as long as the AMX Lighting products are under warranty. AMX Corporation does guarantee the control of dimmable loads that are properly connected to our lighting products. [. . . ] If the IR code for ENTER (function #21) is loaded, an Enter will follow the number. If the channel is greater than or equal to (>=) 100, then IR function 127 or 20 (whichever exists) is generated for the one hundred digit. Uses 'CTON' and 'CTOF' times for pulse times. Syntax: SEND_COMMAND <DEV>, "'CH', <Number>" Variable: channel number = 0 - 199. Example: SEND_COMMAND IR_1, "'CH', 18" The NXC-IRS4 performs the following: · Transmits IR signals for 1 (IR code 11). The transmit time is set with the CTON command. · Waits until the time set with the CTOF command elapses. · Transmits IR signals for 8 (IR code 18). · Waits for the time set with the CTOF command elapses. If the IR code for Enter (IR code 21) is programmed, the IRS4 performs the following steps. · Transmits IR signals for Enter (IR code 21). Waits for the time set with the CTOF command elapses. CP Halt and Clear all active or buffered IR commands, and then send a single IR pulse. You can set the Pulse and Wait times with the 'CTON' and 'CTOF' commands. Syntax: SEND_COMMAND <DEV>, "'CP', <code>" Variable: code = IR port's channel value 0 - 252 (253 - 255 reserved). Example: SEND_COMMAND IR_1, "'CP', 2" Clears the active/buffered commands and pulses IR_1 port's channel 2. CTOF Set the duration of the Off time (no signal) between IR pulses for channel and IR function transmissions. Off time settings are stored in non-volatile memory. This command sets the delay time between pulses generated by the 'CH' or 'XCH' send commands in tenths of seconds. Syntax: SEND_COMMAND <DEV>, "'CTOF', <time>" Variable: time = 0 - 255. Example: SEND_COMMAND IR_1, "'CTOF', 10" Sets the Off time between each IR pulse to 1 second. CTON Set the total time of IR pulses transmitted and is stored in non-volatile memory. [. . . ] For reading current volume levels and displaying bargraphs see CREATE_LEVEL and SEND_LEVEL . The two levels associated with each port of the NXC-VOL4 Control Card are listed in the table below: NXC-VOL4 Levels Port 1 Level 1 2 Description Output #1 Output #2 Level 1 2 Port 2 Description Output #3 Output #4 CREATE_LEVEL This keyword creates an association between a specified level of a device and a variable that will contain the value of the level. This can only appear in the DEFINE_START section of the program. CREATE_LEVEL DEV, Level, Value Parameters: DEV: The device from which to read the level. Value: Variable in which to store the level value. [. . . ]