User manual AMX NXA-UPS1500 UNINTERRUPTIBLE POWER SUPPLY

[. . . ] Operation/Reference Guide NXA-UPS1500 Uninterruptible Power Supply US version (110 Vac) Int'l version (220 Vac) Last Revised: 11/17/2006 AMX Limited Warranty and Disclaimer AMX warrants its products to be free of defects in material and workmanship under normal use for three (3) years from the date of purchase from AMX, with the following exceptions: · · · Electroluminescent and LCD Control Panels are warranted for three (3) years, except for the display and touch overlay components that are warranted for a period of one (1) year. Disk drive mechanisms, pan/tilt heads, power supplies, and MX Series products are warranted for a period of one (1) year. AMX Lighting products are guaranteed to switch on and off any load that is properly connected to our lighting products, as long as the AMX Lighting products are under warranty. AMX does guarantee the control of dimmable loads that are properly connected to our lighting products. [. . . ] When installed and being used, the batteries will be automatically recharged and kept in top condition. Do not install the UPS in an environment with sparks, smoke or gas. Make sure the UPS is completely turned off when moving the UPS from one place to another. It might cause electrical shock if the output is not cut completely. Storage Instructions For extended storage through moderate climate, the batteries should be charged for 12 hours every 3 months by plugging the UPS power cord into the wall receptacle and turn on input breaker on front panel. Repeat this procedure every 2 months under high temperature environment. NXA-UPS1500 Uninterruptible Power Supply 5 IMPORTANT SAFETY INSTRUCTIONS 6 NXA-UPS1500 Uninterruptible Power Supply Setting Up The NXA-UPS1500 Setting Up The NXA-UPS1500 Place the UPS Properly The UPS should be placed in a well-ventilated & low humid environment. Unpacking 1. Standard Package includes: User's Manual AC Input Power Cord Accessories for Tower and Rack Mount Accessories for Tower and Rack Mount FIG. 3 shows the accessories for tower and rack-mounting the UPS: FIG. 3 Accessories for Tower and Rack Mount This unit may require at least two people to install due to its weight. NXA-UPS1500 Uninterruptible Power Supply 7 Setting Up The NXA-UPS1500 Selecting Installation Position It is necessary to select a proper environment to install the unit, in order to minimize the possibility of damage to the UPS and extend the life of the UPS (FIG. 4). · Keep at least 20cm (8") clearance from the rear panel of the UPS from the wall or other obstructions. · Do not block the air-flow to the ventilation openings of the unit. · Please ensure that the installation site environmental conditions are in accordance with the UPS working specifications to avoid overheat and excessive moisture. · Do not place the UPS in a dusty or corrosive environment or near any flammable objects. · This UPS is not designed for outdoor use. FIG. 4 Selecting Installation Position UPS Setup The UPS offers a flexible form factor enabling integration into a wide variety of environments (FIG. The UPS with space-saving design only occupies 2 RU. FIG. 5 UPS Setup If you are installing the UPS in a tower, continue to the following section, "Tower Setup", otherwise; continue to "Rack-Mount Setup". 8 NXA-UPS1500 Uninterruptible Power Supply Setting Up The NXA-UPS1500 Tower Setup Tower Setup - Step One FIG. 6 Tower Setup - Step 1 Tower Setup - Step Two FIG. 7 Tower Setup - Step 2 NXA-UPS1500 Uninterruptible Power Supply 9 Setting Up The NXA-UPS1500 Rack-Mount Setup Rack-Mount Setup - Step One FIG. - Step 1 Rack-Mount Setup - Step Two FIG. - Step 2 10 NXA-UPS1500 Uninterruptible Power Supply Setting Up The NXA-UPS1500 In order to mount the NXA-UPS1500 into an equipment rack, you must use a rack shelf (not included with the UPS), as indicated in FIG. 12. Rack-Mount Setup - Step Three Rack shelf required, not included with the UPS FIG. - Step 3 Rack-Mount Setup - Step Four FIG. [. . . ] Please follow the instructions below: 1. Keep at least 20cm (8 inches) clearance from the rear panel of the EPM from the wall or other obstructions (see FIG. Do not block the air-flow to the ventilation openings of the unit. Please ensure the installation site environmental conditions are in accordance with the EPM working specifications to avoid overheat and excessive moisture (see FIG. [. . . ]