User manual AMX NXA-WAP200G 802.11G WIRELESS ACCESS POINT

[. . . ] instruction manual NXA-WAP200G Modero Wireless Access Point and External Antennas Tou c h Pa n els an d A cc e ss o r ie s AMX Limited Warranty and Disclaimer AMX Corporation warrants its products to be free of defects in material and workmanship under normal use for three (3) years from the date of purchase from AMX Corporation, with the following exceptions: · · · Electroluminescent and LCD Control Panels are warranted for three (3) years, except for the display and touch overlay components that are warranted for a period of one (1) year. Disk drive mechanisms, pan/tilt heads, power supplies, and MX Series products are warranted for a period of one (1) year. AMX Lighting products are guaranteed to switch on and off any load that is properly connected to our lighting products, as long as the AMX Lighting products are under warranty. AMX Corporation does guarantee the control of dimmable loads that are properly connected to our lighting products. [. . . ] Use the information from the Logging into the WAP200G within Access Point Mode section on page 27 to communicate to the WAP200G through a web browser configured for TCP/IP Networking. Press the Administration tab from the bottom row of the Configuration Utility to open the Administration page. From the Commands section of the page, press the on-screen Bridge button to place the WAP200G into the Bridge Mode. When placed in this mode the WAP200G allows devices with only wired 10/100 Ethernet ports such as; printers, PlayStation2s, X-Boxes, PVRs, etc. Click OK (from the confirmation dialog) to reconfirm you want to reboot the WAP200G. A new Temporarily Saved page appears and instructs you to wait a few seconds for the unit to make the necessary changes. Slide the rear AP/BRIDGE switch (on back of the WAP200G) to BRIDGE. Cycle power to the unit before continuing with the setup procedures. Manually cycle power to the WAP200G by disconnecting and re-connecting the power connector from the rear power port on the WAP200G. Open a TCP/IP network configured web browser. Verify the computer and the WAP200G are on the same LAN, within the same IP Address pool. If you are having trouble communicating with your WAP200G, refer to the Troubleshooting section on page 71. Type http://192. 168. 1. 240/ (default WAP200G IP Address) into the web browser's Address field (or the URL field) at the top of the browser window. This is the same location where you type in the resolvable web address such as http://www. amx. com. 192. 168. 1. 240 is the default IP Address of the NXA-WAP200G Wireless Access Point. Once you hit the Enter key, the Login window (FIG. 35) will appear and you will need to enter the following default information: User Name: Admin (Case Sensitive) Password: 1988 14. Click OK to enter the information and access the browser-based configuration screens. NXA-WAP200G Wireless Access Point 41 Wireless Device Communication Setup FIG. 35 WAP200G sample Login page After logging into the WAP200G you can change the default User Name and Password. The WAP200G is now accessible within the Bridge Mode. 15. After connection is re-established, the title 802. 11g Bridge appears below the browser's Address field. The Bridge Mode configuration screens are very similar to the Access Point configuration screens, except for two sections of the Wireless configuration screen and one section within the Advanced configuration screen. Configuring the WAP200G for Secured Bridge Mode Communication After logging into the WAP200G within Bridge Mode, the default Status page appears within the web browser. These read-only values are "pulled" from some of the other user-configurable Configuration Utility pages. [. . . ] A wide area network may be privately owned or rented, but the term usually connotes the inclusion of public (shared user) networks. An intermediate form of network in terms of geography is a metropolitan area network. TCP/IP TKIP WAN Wireless Access point (WAP) A wireless LAN transceiver or "base station" that can connect a wired LAN to one or many wireless devices. Access points can also bridge to each other. There are various types of access points and base stations used in both wireless and wired networks. [. . . ]