User manual AMX PRO-DP16 DECOR PROLINK FLUSH MOUNT KEYPAD PANEL

[. . . ] instruction manual PRO-DP16 Decor 16-Button Wall Panel Lighting Control AMX Limited Warranty and Disclaimer AMX Corporation warrants its products to be free of defects in material and workmanship under normal use for three (3) years from the date of purchase from AMX Corporation, with the following exceptions: · · · Electroluminescent and LCD Control Panels are warranted for three (3) years, except for the display and touch overlay components that are warranted for a period of one (1) year. Disk drive mechanisms, pan/tilt heads, power supplies, and MX Series products are warranted for a period of one (1) year. AMX Lighting products are guaranteed to switch on and off any load that is properly connected to our lighting products, as long as the AMX Lighting products are under warranty. AMX Corporation does guarantee the control of dimmable loads that are properly connected to our lighting products. [. . . ] 4. PRO-DP16 Decor 16-Button PROlink Wall Panel 9 Wiring and Installation 12 VDC power supply PWR (+) GND (-) PRO-DP16 +12 PR+ PRGND Pack 1 Pack 2 +12 PR+ PRGND FIG. 4 PROlink wiring diagram using an external 12 VDC power supply Do not connect the PWR wire to the PROlink connector's PWR (+) terminal on the control system side of the connector. 2. Connect the PROlink connector to the panel (see the Preparing captive wires section on page 8). Check PROlink LED on the rear side of the panel. If the green LED flashes once every 2 seconds, the panel is communicating properly with the Pack. If the LED is on and not flashing, disconnect the PROlink connector and recheck all PROlink connections; reconnect the PROlink connector to the panel and verify the LED is flashing once every 2 seconds. PROlink status LED The green LED on the rear panel of the PRO-DP16 is the PROlink status LED. This LED indicates the communication status of the panel on the PROlink bus: ! Flashing (once every 2 seconds) indicates that PROlink communications are working properly. Full-on indicates that the panel is not communicating with the PROlink bus. Check the PROlink wiring to the Pack and to any other panels. Refer to the Troubleshooting section on page 12 for details. ! Testing The following steps describe how to test the PRO-DP16 to verify it is working properly: 1. Reconnect the power supply to the panel. Check for a blinking green LED on back of the PRO-DP16 panel to verify proper operation. Press Presets 1-10 (default) to cycle through Preset lighting levels. If this test fails, refer to the Troubleshooting section on page 12. 10 PRO-DP16 Decor 16-Button PROlink Wall Panel Wiring and Installation Phasing If you experience erratic ramping with your lights, it is possible that the dimmer control card could be wired out of phase. Check and correct power wiring and repeat the Preset test steps (see Testing). If the green PROlink status LED stays on, or nothing happens when the Presets are selected, check the Pack number value on the dimmer control card. Set the dimmer control cards to different Pack numbers by using the PROlink DIP switch (SW2) to set the Pack number. Refer to the Sample Wiring Diagram section on page 13 for details. Mounting Procedures FIG. 5 shows the mounting dimensions and the wall cutout dimensions for the PRO-DP16. AMX recommends mounting the PRO-DP16 in a standard two-gang wallbox. 4. 745" (120. 5 mm) REF 3. 612" (91. 74 mm) 2. 712" (68. 88 mm) Cutout 0. 90" (22. 86 mm) . 30" (7. 7 mm) From surface 1. 42" (36. 1 mm) Max. Depth 4. 68" (118. 87 mm) 3. 281" 2. 80" (83. 34 mm) (71. 12 mm) . 125 R (3. 175 mm) (Max. ) Install unit using supplied #6-32 machine screws at these locations. Wallplate Mounting bezel Bezel FIG. [. . . ] Dimmer Curves and Keypad Values Curve number Keypad number Description 1 2 3 4 5 6 7 8 9 N O F A B C D E 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 Standard Curve Economy Curve Advance MARK VII ballast PRESCOLITE Intellect ballast % Rolloff % Roll Off 30 % Roll Off Advance MARK X ballast 50% Roll Off; Fans NON-DIM Always Off Always On Modified Standard Curve Transformer 1 Transformer 2 Slow Fade, High End MDM module Low-End Mode The panel must be in Low-End mode in order to record low-end settings for the Packs. Enter Program mode (indicated by the PGM LED). Low End mode is indicated by the LE LED. Select the Pack that you want to record Low-End settings for. [. . . ]