User manual AMX PRO-DP8 DECOR PROLINK FLUSH MOUNT KEYPAD PANEL

[. . . ] instruction manual PRO-DP8 Decor 8-Button Wall Panel Lighting Control AMX Limited Warranty and Disclaimer AMX Corporation warrants its products to be free of defects in material and workmanship under normal use for three (3) years from the date of purchase from AMX Corporation, with the following exceptions: · · · Electroluminescent and LCD Control Panels are warranted for three (3) years, except for the display and touch overlay components that are warranted for a period of one (1) year. Disk drive mechanisms, pan/tilt heads, power supplies, and MX Series products are warranted for a period of one (1) year. AMX Lighting products are guaranteed to switch on and off any load that is properly connected to our lighting products, as long as the AMX Lighting products are under warranty. AMX Corporation does guarantee the control of dimmable loads that are properly connected to our lighting products. [. . . ] Reconnect the PROlink cable to the PROlink bus connector located at the rear of the PRO-DP8. Wiring the PRO-DP8 The PRO-DP8 uses a 4-pin PROlink connector for power and data, located on the back of the panel. ! Use 24-gauge twisted-pair cable for runs of 300 feet (91. 44 meters) and under. Use 22-gauge shielded low-capacitance cable for runs of up to 1, 000 feet (304. 8 meters). Additional panels can be daisy-chained or connected directly to the Pack's terminal. Avoid connecting more than three PRO-D:P:S to a Pack without a separate power supply for the panels (see the Using a PROlink 4-pin connector with an external 12 VDC power supply section on page 9 for details). Preparing captive wires You will need a wire stripper, and flat-blade screwdriver to prepare and connect the captive wires. Strip 0. 25 inch (6. 35 mm) of wire insulation off all wires. Insert each wire into the appropriate opening on the connector according to the wiring diagrams and connector types described in this section. Turn the flat-head screws clockwise to secure the wires in the connector. Do not over-torque the screws; doing so can bend the seating pins and damage the connector. Using a PROlink 4-pin connector for data and power These steps describe how to connect the dimmer Pack's PROlink connector to the PROlink connector (male) on the rear panel of the PRO-DP8 for data and 12 VDC power. Check for short circuits and continuity before connecting panels to the PROlink connector on the dimmer Pack. 1. The captive-wire terminal on the PRO-DP8 is wired to an orange captive-wire terminal on the Pack. Insert each wire into the appropriate opening on the connector, according to the wiring diagram shown in FIG. 1. 8 PRO-DP8 Decor 8-Button Wall Panel Wiring and Installation PRO-DP8 +12 PR+ PRGND Pack 1 Pack 2 +12 PR+ PRGND FIG. 1 Wiring diagram for connecting the PRO-DP8 to a single dimmer control card Additional panels can be daisy-chained or connected directly to the Pack's terminal. Use a 12 VDC power supply when more than three PRO-DP8 panels are used with one Pack. Refer to the Using a PROlink 4-pin connector with an external 12 VDC power supply section on page 9 for more information. Verify PROlink wiring connections are correct before applying power to the Pack. 2. Connect the PROlink connector to the panel (see the Preparing captive wires section on page 8). Locate the green PROlink LED on the rear side of the panel. If the green LED flashes once every 2 seconds, the panel is communicating properly with the Pack. If the LED is on and not flashing, disconnect the PROlink connector and recheck all PROlink connections; reconnect the PROlink connector to the panel and verify the LED is flashing once every 2 seconds. Test to see if the panel recalls a Preset or ramps dimmers (if test fails, refer to the Troubleshooting section on page 12). Using a PROlink 4-pin connector with an external 12 VDC power supply Use a 12 VDC power supply when the distance between the Pack and PRO-DP8 exceeds 1, 000 feet (304. 8 m), or when more than three PRO-DP8 panels are used with one Pack. [. . . ] Press the Up and Down buttons (pushbuttons 6 and 7) to ramp the light level for the selected Preset as needed. Release the Preset button to stop ramping. Preset Ramping mode quits after 6 seconds. Repeat the preceding steps as required for other Presets. PRO-DP8 Decor 8-Button Wall Panel 19 Panel Programming/Operation Setting and changing fade times 1. [. . . ]