User manual AMX RDC-DC RADIA CONTROL CARD, 6 CHANNEL DIMMER-SINGLE PHASE

[. . . ] Installation Sheet RDC-DC Control Card (120, 240, or 277 VAC) The RDC-DC 6-Channel Control Card module controls up to six dimmable channels with six satellite connectors (for RDM series dimmer or switching modules). The RDC-DC is designed for use with the Radia enclosures, in a modular digital dimming system. [. . . ] Test loads for shorts before connecting. Use low-voltage wires with a 300 volt rating or greater. All electrical ratings are for continuous duty. AC lighting loads only. Line Input External +12 V power connector (optional) Connecting RDM Series to the AMX Lighting Master AXlink DIP switch PROlink DIP switch MEMORY PROTECT jumper RESET button 4-pin plug from a RDM series module Note: The 4-pin plugs from the module connector to the 4-pin connector on the master (black plug cover facing up). AXlink connector Dry closure contacts FIG. 2 Connecting RDM series PROlink connector LED indicators Control Ports RDC-DC FIG. 1 RDC-DC control card Pin 4 (GND) Pin 3 (RLY) Pin 2 (DIM) Pin 1 (+12 V) RDC-DC 4-pin module connector Connecting AXlink Connect the 4-pin captive-wire AXlink from the RDC-DC to the Central Controller for AXlink control of the dimming system. PWR AXP AXM GND (optional) PWR AXP AXM GND Central Controller RDC-DC UL and C-UL Ratings: Line Input · 120 VAC, 2W+G, 1Ø, 50/60 Hz, 50 mA · 240 VAC, 2W+G, 1Ø, 50/60 Hz, 25 mA · 277 VAC, 2W+G, 1Ø, 50/60 Hz, 22 mA Control Input: · AXlink · PROlink · Eight dry closures Control Output: · Six control channels · Max. total current sourcing 300 mA @ 12 VDC FIG. 3 AXlink wiring Connecting PROlink: Connect the orange 4-pin captive-wire PROlink connector from the RDCDC to a PRO-DP8 PROlink wall panel. PRO-DP8 +12 PR+ PRGND FIG. 4 PROlink wiring Pack 1 Pack 2 +12 PR+ PRGND Connecting Dry Closures Use the 8 (+ common) dry closures with a WPD8 eight-button wall panel. 1 2 3 4 5 6 7 8 COM Each contact (1 - 8) is preprogrammed with a default preset. Refer to the AMX Lighting Control System instruction manual for details on dry closure default presets and recording new presets. Specifications: · · · · · · · · Dimensions (HW): 10. 0" x 2. 75" (254. 0 mm x 69. 85 mm) 12 VDC power (optional) Torque terminals to 20 in-lbs. wire size: 10 AWG (4 mm²) Wire stripping length: 0. 28" (7 mm) Weight: 1. 2 lbs. (0. 54 kg) Control current: 300 mA for six ports RESET button: By pressing the Reset button, located on the RDC-DC circuit board, it is possible to restart the processor without having to Button/Jumper Information: FIG. 5 Dry closures connection Each contact closure connection (1 - 8) is pre-programmed with a default preset. [. . . ] AMX Corporation reserves the right to alter specifications without notice at any time. 3000 research drive, richardson, TX 75082 USA · 469. 624. 8000 · 800. 222. 0193 · fax 469. 624. 7153 · technical support 800. 932. 6993 [. . . ]