User manual AMX RDD-DM6 6-CHANNEL INTEGRATED DIMMER MODULE

[. . . ] Installation Sheet RDD-DM6 6-Channel Integrated Dimmer Module 120, 240, 277 VAC The RDD-DM6 Six-Channel Integrated Dimmer Module controls up to six dimmed channels with six onboard 10 A dimmers. The RDD-DM6 is designed for use with the RDA series of enclosures, in a AMX LightingTM modular digital dimming system. [. . . ] All electrical ratings are for continuous duty. This module may require extra power from the AXlink connection or an external power supply connected to the control card. 10. 00" (254. 00 mm) AXlink address DIP switch PROlink address DIP switch RESET button MEMORY PROTECT jumper Connecting AXlink: Connect the 4-pin captive-wire AXlink from the RDD-DM6 to the Central Controller for AXlink control of the dimming system. PWR RDD-DM6 Mounting points DRY CLOSURES AXlink connector PROlink connector External +12V power connector (optional) AXP AXM GND (optional) PWR AXP AXM GND Central Controller FIG. 2 Connecting AXlink Connecting PROlink: Connect the orange 4-pin captive-wire PROlink connector from the RDD-DM6 to a PRO-DP8 PROlink wall panel. PRO-DP8 +12 PR+ PRGND Pack 1 Pack 2 +12 PR+ PRGND FIG. 1 RDD-DM6 6-channel Integrated Dimmer Module RDD-DM6 UL and C-UL Ratings (per circuit) Input · 120, 240, 277 VAC, single phase, 3-wire, 50/60 Hz, 2400 W, one feed · 120, 240, 277 VAC, single phase, 4-wire, 50/60 Hz, 4800 W, two feed Output · · · · 1200 W max. per channel @120, 240, 277 VAC 2400 W max. total, all six channels on with 2400 W feed 4800 W max. total, all six channels on with dual 2400 W feeds Feed circuit #1 goes to dimmer 1, 3, and 5; feed circuit #2 goes to dimmer 2, 4 and 6 Incandescent Low-voltage Neon, cold-cathode Motors Fans FIG. 3 Connecting PROlink Line-in Connections: Dual 2400 W Inputs Using two feeds for line 1 and line 2 provides two, 2400 W inputs. Suggested Switched Loads · · · · · Bridging line 1 and line 2 provides a single 2400 W input. 20 A Bridged 2400 W Input FIG. 4 Line-in Connections Connecting Dry Closures: Use the 8 (+ common) dry closures with a WPD8 eight-button wall panel. Setting AXlink and PROlink Address Numbers: AXlink Address PROlink Address Test Each contact (1 - 8) is preprogrammed with a default preset. Refer to the AMX Lighting Control System instruction manual for details on dry closure default presets and recording new presets. Set the AXlink address number (1-255) for the RDD-DM6. This number must match the device number in your Axcess program. Use the PROlink DIP switch to set the PROlink address number for the RDD-DM6 (1-10). Pin 8 on the PROlink DIP switch is a test switch that turns all circuits on to full. 1 2 3 4 5 6 7 8 COM FIG. [. . . ] AMX reserves the right to alter specifications without notice at any time. 3000 research drive, richardson, TX 75082 USA · 469. 624. 8000 · 800. 222. 0193 · fax 469. 624. 7153 · technical support 800. 932. 6993 [. . . ]