User manual AMX RDM-2DC DUAL DC MODULE, 1,920 W (X2), 0-12 VDC
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual AMX RDM-2DC DUAL DC MODULE, 1,920 W (X2), 0-12 VDC. We hope that this AMX RDM-2DC DUAL DC MODULE, 1,920 W (X2), 0-12 VDC user guide will be useful to you.
Lastmanuals help download the user guide AMX RDM-2DC DUAL DC MODULE, 1,920 W (X2), 0-12 VDC.
Manual abstract: user guide AMX RDM-2DC DUAL DC MODULE, 1,920 W (X2), 0-12 VDC
Detailed instructions for use are in the User's Guide.
[. . . ] Installation Sheet
RDM-2DC Dual DC Dimmer Module 1920 W, 0-10 VDC (x2)
The RDM-2DC Dual DC Module is a 1920 W module used for the dimming of fluorescent ballast loads. It uses a 0 to 10 VDC current sinking for use with four-wire ballasts. [. . . ] Use low-voltage wires with a 300 volt rating or greater. All electrical ratings are for continuous duty. Test loads for shorts before connecting. This module may require extra power from the AXlink connection or an external power supply connected to the control card.
Connecting the RDM-2DC to the AMX Lighting Master
Pin 4 (GND) Pin 3 (RLY) Pin 2 (DIM)
High voltage
Line in Load out
Pin 1 (+12 V) RDM-2DC 4-pin module connector GND 3 (-) 2 (DIM) 1 (+) Fuses 4-pin plug from RDM series module Note: The 4-pin plugs from the module connector to the 4-pin connector on the master (black plug cover facing up).
Low - out (LV) voltage + out (LV)
FIG. 2 Connecting the RDM-2DC and AMX Lighting Master
Lighting Application Drawings
Low-voltage control wiring: 4-pin connector to AMX Lighting master controller Neutral Line in (HOT) + Ballast Load Neutral Florescent Ballast
FIG. 1 RDM-2DC
RDM-2DC UL and C-UL Ratings
· · · · 120 VAC, 50/60 Hz, 1920 W 277 VAC, 50/60 Hz, 1920 W Control Out: 50 mA, 12 VDC sinking Four-wire dimmable ballasts, like Advance Transformer Mark VIITM or the Energy Savings SuperDimTM series Dimensions (HW): 10" x 2. 75" (25. 4 cm x 6. 99 cm) Non-phase dependant Use wires rated at 75°C (167°F) Torque terminals to 20 in-lbs. wire size: 10 AWG (4 mm²) Wire stripping length: 0. 28" (7 mm) Weight: 2. 6 lbs. (1. 180 kg) BTU/hr: 150 Control current: 125 mA @ 12 VDC
Circuit breaker panel
Suggested Dimmed Loads
Specifications
· · · · · · · · ·
FIG. 3 RDM-2DC application wiring
The fuses protect the dimming circuit from a low impedance load. · The fuse will blow if it were incorrectly wired · Catastrophic ballast failure · Reversing switched and dimmed circuits · Reversing dimmed and line circuits. [. . . ] AMX Corporation reserves the right to alter specifications without notice at any time. 3000 research drive, richardson, TX 75082 USA · 469. 624. 8000 · 800. 222. 0193 · fax 469. 624. 7153 · technical support 800. 932. 6993 [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE AMX RDM-2DC DUAL DC MODULE, 1,920 W (X2), 0-12 VDC
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual AMX RDM-2DC DUAL DC MODULE, 1,920 W (X2), 0-12 VDC will begin.
, 0-12 VDC.webp "Mode d'emploi AMX RDM-2DC DUAL DC MODULE, 1,920 W (X2), 0-12 VDC")
