User manual AMX TOUCH PANEL INTERFACE 4

[. . . ] Operation/Reference Guide NXP-TPI/4 NetLinx Touch Panel Interface 4 Firmware version G4 Touch Panels Document ID: 060-004-2602 Initial Release: / Last Revised: 06/19/2006 AMX Limited Warranty and Disclaimer AMX warrants its products to be free of defects in material and workmanship under normal use for three (3) years from the date of purchase from AMX, with the following exceptions: · · · Electroluminescent and LCD Control Panels are warranted for three (3) years, except for the display and touch overlay components that are warranted for a period of one (1) year. Disk drive mechanisms, pan/tilt heads, power supplies, and MX Series products are warranted for a period of one (1) year. AMX Lighting products are guaranteed to switch on and off any load that is properly connected to our lighting products, as long as the AMX Lighting products are under warranty. AMX does guarantee the control of dimmable loads that are properly connected to our lighting products. [. . . ] Video Settings: · The Black & White button toggles the Black & White display mode. · The Sharpness button toggles the Interpolate (Sharpness) feature. · The Interlace button toggles the Interlacing feature. Status: Version: Displays whether or not a video-sync signal is detected. Displays the firmware version being used by the selected TP4-VID card. NXP-TPI/4 NetLinx Touch Panel Interface 63 Firmware Pages and Descriptions Video Adjustment Page Elements (Cont. ) Format: Allows you to press this blue field and cycle through a choice of available video formats (NTSC, PAL, SECAM, or Auto detect). Input: Allows you to cycle through a choice of available video inputs (either Composite or S-Video). Brightness: Contrast: Saturation: Hue: Use the UP/DN buttons to alter the brightness level of the incoming signal. · Range = 0 - 255, default = 128. Use the UP/DN buttons to alter the contrast level of the incoming signal. · Range = 0 - 255, default = 128. Use the UP/DN buttons to alter the color saturation level of the incoming signal. · Range = 0 - 255, default = 128. Use the UP/DN buttons to alter the hue level of the incoming signal. · Range = 0 - 255, default = 128. If the TPI/4 is powered Off, any preset TPD4 Video pages must be reset if you are using an S-Video input. By default, the Input is set to Composite. If the video pages appear blank upon restart of the unit, simply toggle the Input setting to S-Video. Video Adjustment - RGB Setup The RGB Setup page (FIG. 47) (accessed by pressing the Video Adjustment button on the Setup page and then selecting a SLOT # from the option bar which contains a TP4-RGB card) sets the RGB properties of the incoming signal. These slots are labeled at the rear of the unit. Firmware version of TP4-RGB card Output resolution Once you are done making your adjustments, click SAVE SETTINGS. Incoming signal shown in the background Pressing this area activates the Full Screen Edit mode FIG. 47 RGB Adjustment page (showing the default values) 64 NXP-TPI/4 NetLinx Touch Panel Interface Firmware Pages and Descriptions The elements of the RGB Adjustment page are described in the table below: RGB Adjustment Page Elements Back: Connection Status icon: Saves the changes and returns you to the previously active touch panel page. This visual display of the connection status allows the user to have a current update of the TPI/4's connection status regardless of what page is currently active. · A Lock only appears on the icon if the TPI/4 has established a connection with a currently secured target Master (requiring a username and password). Settings: · The Default Settings button sets the RGB settings to their default values (indicated in this table). [. . . ] Overflow continues to work until a filed with no overflow value is set or there are no more fields left (i. e. If a character is typed and that characters appear in the Next Field list, the keyboard should move the focus to the next field. For example, when entering time, a ":" is used as a next field character. If you hit "1:2", the 1 is entered in the current field (hours) and then the focus is moved to the next field and 2 is entered in that field. [. . . ]