User manual AOC 173P

[. . . ] TABLE OF CONTENTS FOR YOUR SAFETY -------------------------------------------------- 1 SAFETY PRECAUTIONS -------------------------------------- 2 SPECIAL NOTES ON LCD MONITORS ------------------- 3 BEFORE YOU OPERATE THE MONITOR --------------------FEATURES -------------------------------------------------------PACKING LIST --------------------------------------------------CONTROLS AND CONNECTORS -------------------------ADJUSTING THE VIEWING ANGLE ----------------------3 3 3 5 6 OPERATING INSTRUCTIONS ------------------------------------- 7 GENERAL INSTRUCTIONS ---------------------------------- 7 HOW TO ADJUST A SETTING ------------------------------ 9 ADJUSTING THE PICTURE --------------------------------- 10 PLUG AND PLAY ----------------------------------------------- 12 TECHNICAL SUPPORT(FAQ) ------------------------------------ 13 ERROR MESSAGE & POSSIBLE SOLUTION -------- 14 APPENDIX -------------------------------------------------------------- 15 SPECIFICATIONS ------------------------------------------ 15-16 FACTORY PRESET TIMING TABLE ---------------------- 17 CONNECTOR PIN ASSIGNMENT ------------------------- 18 1 Before operating the monitor, please read this manual thoroughly. This manual should be retained for future reference. FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS) NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] Connect the AC-power cord into your LCD monitor's External Adapter input socket, and then plug the other end of External adapter to LCD monitor's DC-power-input. The AC-power cord may be connected to either a wall power outlet or the power outlet socket on your PC, depending on the type of power cord supplied with your LCD monitor. NOTES A certified power supply cord has to be used with this equipment. The relevant national installation and/or equipment regulations shall be considered. A certified power supply cord not lighter than ordinary polyvinyl chloride flexible cord according to IEC 60227 (designation H05VV-F 3G 0. 75mm2 or H05VVH2-F2 3G 0. 75mm2) shall be used. Alternative a flexible cord be of synthetic rubber according to IEC 60245 (designation H05RR-F 3G 0. 75mm2) shall be used. 5 CONTROLS AND CONNECTORS VIDEO CABLE Connecting the D-Sub Cable: Connect one end of the 15-pin D-Sub cable to the back of the monitor and connect the other end to the computer's D-Sub port. Connecting the Power Cord: Plug the AC-power cord into the External Adapter. Then plug the DC-jack power cable into DC-IN Inlet. Connecting the DVI Cable: Connect one end of the 24-pin DVI cable to the back of the monitor and connect the other end to the computer's DVI port. Caution: If the AC outlet is not grounded (with three holes), install the proper grounding adapter (not supplied). Figure 1 Connecting Cables 1. 3. DC-Jack Power Cable AC Power Cord 2. 4. Signal Cable DVI Cable 6 ADJUSTING THE VIEWING ANGLE · For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor's angle to your own preference. · Hold the stand so you do not topple the monitor when you change the monitor's angle. · You are able to adjust the monitor's angle from -5° to 20°. 20° Figure 2 NOTES · Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen. · Careful attention is required not to catch your fingers or hands when you change the angle. 7 OPERATING INSTRUCTIONS GENERAL INSTRUCTIONS Press the power button to turn the monitor on or off. The other control buttons are located at front panel of the monitor (See Figure 3). By changing these settings, the picture can be adjusted to your personal preferences. · The power cord should be connected. · Connect the video cable from the monitor to the video card. · Press the power button to turn on the monitor position. The power indicator will light up. Figure 3 External Control Button EXTERNAL CONTROLS 1. Power Key 8 FRONT PANEL CONTROL · Power Button: Press this button to switch ON/OFF of monitor's power. · MENU / ENTER : Activate OSD menu when OSD is OFF or activate/de-activate adjustment function when OSD is ON or Exit OSD menu when in Brightness/ Contrast Adjust OSD status. · Contrast : Adjust contrast or function adjust. · Brightness: Adjust brightness or function adjust. · Auto Adjust button / Exit: 1. When OSD menu is in active status, this button will act as EXIT-KEY (EXIT OSD menu). When OSD menu is in off status, press this button over 2 seconds to activate the Auto Adjustment function. The Auto Adjustment function is used to set the HPos, VPos, Clock and Focus. · Power Indicator: Blue -- Power On mode. [. . . ] *Inspect monitor's video cable and make sure none of the pins are bent. *Make sure computer is operational by hitting the CAPS LOCK key on the keyboard while observing the CAPS LOCK LED. The LED should either turn ON or OFF after hitting the CAPS LOCK key. Missing one of the primary *Inspect the monitor's video cable and make sure that none of the pins are colors (RED, GREEN, or bent. [. . . ]