User manual AOC 416V

[. . . ] These blocks are notes, cautions, and warnings, and they are used as follows: NOTE: A NOTE indicates important information that helps you make better use of your computer system. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates the potential for bodily harm and tells you how to avoid the problem. Some warnings may appear in alternate formats and may be unaccompanied by an icon. [. . . ] This will protect the monitor from damage due to power surges. Do not overload power strips and extension cords. Overloading can result in fire or electric shock. Never push any object into the slot on the monitor cabinet. It could short circuit parts causing a fire or electric shock. Do not attempt to service the monitor yourself; opening or removing covers can expose you to dangerous voltages and other hazards. Please refer all servicing to qualified service personnel. To ensure satisfactory operation, use the monitor only with UL listed computers which have appropriate configured receptacles marked between 100 - 240V AC, Min. The wall socket shall be installed near the equipment and shall be easily accessible. For use only with the attached power adapter (Output 12Vdc) which have UL, CSA listed license(Only for monitors with power adapter). Setup the stand and base Please setup or remove the base following below steps. Adjusting Viewing Angle For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor's angle to your own preference. Hold the stand so you do not topple the monitor when you change the monitor's angle. You are able to adjust the monitor's angle from -5°to 15¡ã. NOTE: Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen. Attaching the Cables Cable Connections On Back of Monitor and Computer 1. Power 2. Analog 3. DVI Turn off your computer before performing the procedure below. Connect the power cable to the AC port on the back of the monitor. Connect one end of the 15-pin D-Sub cable to the back of the monitor and connect the other end to the computer's D-Sub port. Turn on your monitor and computer. If your monitor displays an image, installation is complete. If it does not display an image, see Troubleshooting. Attaching Wall Mounting Arm Preparing to Install An Optional Wall Mounting Arm This monitor can be attached to a wall mounting arm you purchase separately. Follow the manufacturer's instructions to assemble the wall mounting arm. Place the wall mounting arm onto the back of the monitor. Line up the holes of the arm with the holes in the back of the monitor. Insert the 4 screws into the holes and tighten. [. . . ] Display Color Dot Clock Horizontal scan range Horizontal scan Size(Maximum) Vertical scan range Vertical scan Size(Maximum) Optimal preset resolution Highest preset resolution Plug & Play Input Connector Input Video Signal Power Source Power Consumption Connector Type Signal Cable Type Dimensions & Weight: Height (with base) Width Depth Weight (monitor only) Weight (with packaging) Temperature: Operating Non-Operating Humidity: Operating Non-Operating Altitude: Operating Non-Operating 416V TFT Color LCD 609. 6mm diagonal 0. 270mm(H) x 0. 270mm(V) R, G, B Analog lnterface & Digital Interface H/V TTL 16. 7 million Colors 165 MHz 30 kHz - 83 KHz 518. 4mm 55 Hz - 75 Hz 324. 0mm 1920 x 1200 (60 Hz) 1920 x 1200 (60 Hz) VESA DDC2B/CI D-Sub 15pin & DVI-D Analog: 0. 7Vp-p(standard), 75 OHM, Positive & DVI-D Digital Interface (TMDS) 100~240VAC, 47~63Hz Active < 49W Standby < 2W 15-pin Mini D-Sub & DVI-D Detachable 392. 7 mm (463. 3) 561. 8 mm 114. 6 mm 6. 8 kg 9. 0 kg 0° to 50° -20¡ãto 60° 10% to 85% (non-condensing) 5% to 80% (non-condensing) 0~ 3000m (0~ 10000 ft ) 0~ 5000m (0~ 15000 ft ) LCD Panel Resolution Physical Characteristics Environmental EPA ENERGY STAR ® ENERGY STAR® is a U. S. As an ENERGY STAR® Partner, AOC International (Europe) GmbH has determined that this product meets the ENERGY STAR® guidelines for energy efficiency. Preset Display Modes HORIZONTAL STAND Dos-mode VGA Mac VGA VGA SVGA Mac SVGA XGA Mac SXGA WSXGA+ UXGA WUXGA RESOLUTION 640 x 350 720 x 400 640 x 480 640 x 480 640 x 480 640 x 480 800 x 600 800 x 600 800 x 600 800 x 600 832 x 624 1024 x 768 1152 x 864 1152 x 870 1280 x 960 1280 x 1024 1280 x 1024 1680 x1050 1600 x 1200 1600 x 1200 1600 x 1200 1600 x 1200 1920 x 1200 FREQUENCY(kHZ) 31. 469 31. 469 31. 469 35 37. 861 37. 5 35. 156 37. 879 48. 077 46. 875 49. 726 48. 363 67. 5 68. 681 60 67. 981 79. 976 65. 29 75 93. 75 81. 25 87. 5 74. 038 FREQUENCY(Hz) 70. 086 70. 087 59. 94 66. 667 72. 809 75 56. 25 60. 317 72. 188 75 74. 551 60. 004 75 75. 062 60 60. 02 75. 025 59. 954 60 75 65 70 59. 95 VERTICAL Pin Assignments Pin Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 15-Pin Side of the Signal Cable Video-Red Video-Green Video-Blue N. C. Ground GND-R GND-G GND-B +5V Detect Cable N. C. DDC-Serial data H-sync V-sync DDC-Serial clock Pin No. [. . . ]