User manual AOC LM700

[. . . ] LM-700 LM-700 17 inch TFT LCD Monitor User's Manual by Envision Peripherals, Inc. www. aocmonitor. com Before operating your monitor, please read this manual thoroughly. LM-700 1 v3_123102 For Your Safety FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] 18 AWG, type SJT or SVT three conductors cord with one end terminating with a male grounded plug, rated 10A, 250V, CEE-22. The other end must terminate with a molded-on type connector body, rated 10A, 250V, having standard CEE-22 female configuration. 4 LM-700 v3_123102 Before You Operate the Monitor Installing & Removing the Base LM-700 General Features: · 17" (43. 2cm) TFT Color LCD Monitor · Crisp, Clear Display for Windows · Supports Resolutions up to 1280 X 1024 pixels @75Hz · EPA ENERGY STAR® · Ergonomic Design · Space Saving, Compact Case Design LM-700 Package Contents The box that your monitor was shipped in should have included the following items: 1. 5 LM-700 LCD Monitor Power Adaptor Power Cord Windows 95/98/2000/ME/XP INF Driver Disk Quick Start Guide Booklet (Containing Warranty & Safety v3_123102 Before You Operate the Monitor Connecting the Wires Using the Power Cord Supplied LM-700 1. Connect the built-in video cable into the 15-pin connector on the back of your computer and tighten the two screws. Connect the power cord into the power adaptor. Plug the other end of the power cord into a grounded AC outlet or UL-approved power strip. Connect the power adaptor into the DC IN socket on the back of the monitor. Caution: Make sure the power cord is the correct type that is required in your area. This LCD monitor has a universal power supply that allows operation in either 100/120V AC or 220/240V AC voltage areas (no user adjustment is required). If the AC outlet is not grounded (with three holes), install the proper grounding adapter (not supplied). LM-700 6 v3_123102 Before You Operate the Monitor LM-700 Connecting the Wires Using An Optional Power Cord (Not Supplied) The power cord supplied with your monitor can only be connected to a grounded electrical wall socket or power strip. If you wish to connect your monitor to a power supply using the power input socket on the back of your computer, you must purchase a power cord with CEE-22 terminated connectors (see illustration above). Follow these steps: 1. Connect the built-in video cable into the 15-pin connector on the back of your computer and tighten the two screws. Connect the power cord into the power adaptor. Plug the other end of the power cord into the power output socket on your PC. Connect the power adaptor into the DC IN socket on the back of the monitor. LM-700 7 v3_123102 Before You Operate the Monitor LM-700 Preparing to Install An Optional Wall Mounting Arm (Not supplied) This monitor can be attached to a wall mounting arm you purchase separately. Pull the screw covers off the back of the monitor. Follow the manufacturer's instructions to assemble the wall mounting arm. See next page for further installation instructions. 8 v3_123102 Before You Operate the Monitor Install An Optional Wall Mounting Arm (Not supplied) LM-700 Follow these steps to finish installing the wall mounting arm: 1. Place the wall mounting arm onto the back of the monitor. Line up the holes of the arm with the holes in the back of the monitor. Insert the 4 screws into the holes and tighten. Insert the power cable into the slot on the back of the monitor. AOC's Model LM700 is compatible with the Ergotron line of mounting and arm solutions. [. . . ] · Make sure your computer is operating correctly by pressing the CAPS LOCK key and observing whether the CAPS LOCK light turns ON or OFF. · Inspect the video cable and make sure that none of the pins are bent. · Make sure the video cable is properly connected to the computer. No Plug & Play Picture is fuzzy Picture bounces or a wave pattern is present in the picture Power LED is ON (green or orange light is ON) but there is no video or picture. Missing one of the primary colors (RED, GREEN, or BLUE) LM-700 14 v3_123102 Technical Support (FAQ) Problem Screen image is not centered or sized properly Picture has color defects (white does not look white) Poor brightness or contrast Horizontal or vertical disturbances on the screen 1CLOCK LM-700 Possible Solution · Adjust the CLOCK1 and FOCUS2 settings or press the AUTO button to automatically re-configure the monitor's settings. [. . . ]