User manual AOPEN I975XAYDG

[. . . ] Chapter Table of Contents Table of Contents 1. 1 Saftey Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 1. 2 A Thank-you Note Before You Get Start. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 1. 3 Features of This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 1. 4 Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Chapter Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Chapter 2 Introduction to This Motherboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2. 1 How does your motherboard look like?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2. 2 Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2. 3 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Chapter 3 Hardware Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Turn off the system and unplug the AC power. Remove ATX power cable from connector PWR2. Locate JP14 and short pins 2-3 for a few seconds. Return JP14 to its normal setting by shorting pin 1 & pin 2. Connect ATX power cable back to connector PWR2. Pin 1 1 Normal (Default) 1 Clear CMOS JP14 Clear CMOS Jumper Tip: When should I Clear CMOS?Troubleshooting. . . 45 JP28 Keyboard/ Mouse Wakeup Jumper This motherboard provides keyboard / mouse wake-up function. You can use JP28 to enable or disable this function, which could resume your system from suspend mode with keyboard or mouse. The factory default setting is "Disable" (1-2), and you may enable this function by setting the jumper to 2-3. Pin 1 1 1 Disable Enable (Default) JP28 PS2 KB/Mouse Wakeup Jumper 46 JP4 and JP5 Front Side Bus Clock Frequency Jumper Front Side Bus, FSB is also known as the Processor Bus, Memory Bus, or System Bus and connects the CPU with the main memory and is used to connect to other components within the computer. Front Side Bus Frequency Jumper JP4 JP5 Normal (Default) 1 1 JP4 JP5 1 1 FSB 800MHz (Take off Jumpers) Over-Clocking 47 Chapter 4 Special Features and Utilities Chapter 4 Special Features and Utilities 4. 2 Other Useful Features With excellent design ability of R&D team, AOpen boasts for its various powerful and handy features that come with our product like follows. You are welcomed to visit our technical website to learn more about those features. http://english. aopen. com. tw/tech/techinside 48 Chapter 5 Setting BIOS Chapter 5 Setting BIOS 5. 1 Introduction System parameters can be modified by going into BIOS Setup menu; this menu allows you to configure the system parameters and save the configuration into the 128 bytes CMOS area (normally in the RTC chip or in the main chipset). The Phoenix-Award BIOSTM that installed in the Flash ROM of the motherboard is a custom version of an industry standard BIOS. The BIOS provides critical low-level support for standard devices such as hard disk drives, serial and parallel ports. AOpen's R&D engineering team had optimized most BIOS settings of this motherboard. However, some default settings of BIOS cannot fine-tune those sections that controlled by chipset. Therefore, this chapter is intended to guide you and help you to configure some other settings. To enter BIOS setup menu, press <Del> when POST (Power-On Self Test) screen is shown on your monitor. 49 5. 2 How To Use Phoenix-AwardTM BIOS Setup Program Generally, you can use arrow keys to highlight items that you want to choose, press <Enter> key to select, and use <Page Up> and <Page Down> keys to change setting values. You can press <Esc> key to quit Phoenix-AwardTM BIOS setup program. The following table provides details about how to use keyboard in the Phoenix-AwardBIOS setup program. Key Description Page Up or + Page Down or Enter Esc Up Arrow Down Arrow Left Arrow Right Arrow F10 Change setting to next value or increase the value. Change setting to previous value or decrease value. In main menu: Quit without saving any changes. In sub menu: Exit current menu to main menu. Move the light bar to left side of menu. [. . . ] All you have to do is just click on the "GO", and no more steps afterward, of all listed drivers, grey checks indicate necessary drivers; you cannot click them off. Red checks can be disabled if you don't want to install them now. Press the icon will prompt the "Install Driver" page. You may also press "Back" to return to the Main page. Once clicking "GO", EzInstall will run the installing procedure automatically, and prompt a reboot dialog (Some drivers or utilities may skip the reboot part). 73 6. 2 Installing Utilities Installing Utilities is virtually the same as installing drivers. AOpen provides you many friendly and powerful utilities to manage your system. [. . . ]