User manual APC BACK-UPS BX1500LCD

[. . . ] 2 ® 1 CONTENTS RJ-11 RJ-45 RJ-11 RJ-45 2 CONNECT BATTERY CARTRIDGE* w w w. apc. com Back UPS® BR1300LCD Back-UPS® BR1500LCD Back UPS® BX1300LCD Back-UPS® BX1500LCD User's Manual USB RJ-45 1 Coax Coax 2 Æ Note: This diagram is also used for battery cartridge replacement. 3 OPERATING ENVIRONMENT 4 CONNECT EQUIPMENT / POWER FAX 3 5 CHECK BUILDING WIRING FAULT INDICATOR If the rear panel Building Wiring Fault (red) indicator is lit, a potential shock hazard exists due to one of the following conditions: · Open or high resistance ground · Hot and Neutral polarities are reversed · Overloaded neutral circuit Improper building wiring should be corrected by a qualified electrician. Do not use the Back-UPS until the condition that caused the fault is corrected. Note: Improper building wiring will not prevent the BackUPS from operating, but it will limit its protection capability. 6 CONNECT MODEM/PHONE/Network and TVSS Ground If needed, the Back-UPS features a TVSS ground screw for connecting the ground lead of any additional stand alone surge suppression devices, such as an APC ProtectNet product; or any electronic device with an external ground connection. 8 CONNECT DATA LINE AND INSTALL SOFTWARE ON COMPUTER (Optional) RJ-45/ RJ-11 RJ-45/ RJ-11 RJ-45/ RJ-11 RJ-45/ RJ-11 From stand alone data line surge suppressor or electronic device CABLE IN To USB Port USB RJ-45 CABLE OUT Building Wiring Fault To USB Port 32 - 104oF (0 - 40oC) Computer Printer or Scanner Phone Jack External Disk or CD / DVD Drive Monitor Computer Modem Port OR Phone or Fax 2 CABLE IN CABLE OUT 7 CONNECT COAXIAL CABLES Coaxial Cable CABLE IN From Cable Provider To Cable Modem 1. Insert CD into computer, and on-screen instructions should appear automatically. [. . . ] The unit will mute the alarm all the time except for faults. DISPLAY AVR ON BATT LOAD ON LINE CLICK When you press the DISPLAY button the third time, the ESTIMATED RUN TIME IN MINUTES is displayed. In this example, the value is 18 minutes. ON LINE DISPLAY LOAD Warning 2 - Battery Backup Overload This warning indicates that there is a backup battery (ONBATT) overload condition. This is indicated by the flashing overload icon. LOAD When AVR is illuminated on the LCD, it indicates that the automatic voltage regulation (AVR) circuitry is in Boost mode. AVR compensates for excessively low voltage conditions without going on battery. In this example, 90 V is displayed. LOW SENSITIVITY IN V LOW ON BATT AVR DISPLA Y ESTIMATED RUN TIME IN MINUTES Sensitivity kW MID HIGH Flashing A typical condition where sensitivity adjustments would be appropriate is with an AC line input, and with the UPS off. Press and hold the power ON/OFF pushbutton in for 10 seconds. The unit will go into "sensitivity programming mode". Use the ON/OFF button to select the LO, MID or HIGH range. LO displays one block, MID is three blocks, and High is five blocks. Sensitivity programming mode is also discussed on Page 3. SENSITIVITY When you press the DISPLAY button a fourth time in ON LINE mode, the LOAD in Watts (W) is displayed, in this example 760 W is displayed. Warning 3 - Online Bad Battery LOAD ON LINE LOAD ON LINE When you press the DISPLAY button a third time the battery backup (ON BATT) output (OUT) voltage (V) is displayed, in this example it is 115 V. ON BATT LOAD This warning indicates that you are in ONLINE mode, and you have a bad battery, indicated by the flashing bad battery icon. IN V DISPLAY W V OUT Flashing When you press the DISPLAY button a fifth time, the online LOAD as a percentage (%) is displayed, in this example it is 82%. Warning 4 - Battery Backup Low Battery LOAD ON LINE LCD Full Time Display Mode LOAD LOW ON BATT When you press the DISPLAY button a fourth time the battery backup (ON BATT) input voltage (IN) is displayed. % LOAD LOAD This warning indicates that the battery is low. This is indicated by the word LOW, and the Battery Capacity indicator bar flashing. V Flashing The LCD can be set to full time display mode by performing the following steps: 1. Ensure the unit is connected to utility input power, and the power on/off switch is turned off (no power is supplied to the output connectors). Press the DISPLAY/HOLD TO MUTE pushbutton, and hold it in for 10 seconds. Disconnect non-essential equipment from the Back-UPS. Switch on the Back-UPS, and plug in devices one at a time. If the circuit breaker trips again, disconnect the device that caused the breaker to trip. Connect the battery cartridge (see Connect Battery Cartridge). Consider adjusting the transfer voltage and sensitivity. See Transfer Voltage and Sensitivity Adjustment. Unplug the device from the 'Surge Only' outlet, and move to a 'Battery Backup' outlet. Verify the Back-UPS's plug is fully inserted into the wall, and power is present at the wall outlet by plugging in a known good device. Consider adjusting the transfer voltage and sensitivity. [. . . ] If requested, this information must be provided to the telephone company. SERVICE If the Back-UPS arrived damaged, notify the carrier. If the Back-UPS requires service, do not return it to the dealer. Consult the Troubleshooting section to eliminate common problems. If the problem persists, go to http://www. apc. com/support/. [. . . ]