User manual APC SMART-UPS RT 5000VA

[. . . ] i Manual Revisions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i Table of Contents Product Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Package Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Advertisement Lifetime: D-Link SMART-UPS RT 5000VA User Manual 62 Section 3 - Configuration 6to4 My IPv6 Select 6to4 from the drop-down menu. Connection Is: 6to4 Address: Enter the IPv6 settings supplied by your ISP. 6to4 Relay: Enter the IPv6 relay supplied by your ISP. Primary/Secondary Enter the primary and secondary DNS server addresses. DNS Address: LAN IPv6 Address: Enter the LAN (local) IPv6 address for the router. LAN Link-Local Displays the Router’s LAN Link-Local Address. Address: Enable Automatic Check to enable the Automatic IPv6 Address Assignment feature. IPv6 Address Assignment: Autoconfiguration Select Stateful (DHCPv6), SLAAC + RDNSS or SLAAC + Stateless Type: DHCPv6. Router Enter the IPv6 Address Lifetime (in minutes). Advertisement Lifetime: D-Link SMART-UPS RT 5000VA User Manual 63 Section 3 - Configuration 6rd My IPv6 Select 6rd from the drop-down menu. Connection Is: Enable Hub and Check this box if you want to minimize the number of routes to the Spoke Mode: destination by using a hub and spoke method of networking. IP Address: Enter the IP address of the computer on your local network that you want to allow the incoming service to. If your computer is receiving an IP address automatically from the router (DHCP), your computer will be listed in the “Computer Name” drop-down menu. Private Port/ Enter the port that you want to open next to Private Port Public Port: and Public Port. The private and public ports are usually the same. The public port is seen from the Internet side, and the private port is used by the application on the computer within your local network. Protocol: Select TCP, UDP, or Both from the drop-down menu. Schedule: The schedule of time when the Virtual Server Rule will be enabled. The schedule may be set to Always, which will allow the particular service to always be enabled. You can create your own times in the Tools > Schedules section. Inbound Filter: Select Allow All (most common) or a created Inbound filter. You may create your own inbound filters in the Advanced > Inbound Filter page. Advanced D-Link SMART-UPS RT 5000VA User Manual 68 Section 3 - Configuration Port Forwarding This page will allow you to open a single port or a range of ports. [. . . ] Click on Start > Control Panel > Network and Internet > Network and Sharing Center > Manage Network Connections. Click on Start > Control Panel > Network Connections. From the desktop, right-click My Network Places > Properties. Step 2 Right-click on the Local Area Connection which represents your network adapter and select Properties. Step 3 Highlight Internet Protocol (TCP/IP) and click Properties. [. . . ]