User manual APELCO GPS11

[. . . ] Distributed by Any reference to Raytheon or RTN in this manual should be interpreted as Raymarine. The names Raytheon and RTN are owned by the Raytheon Company. Apelco GPS11 Installation and Operation Handbook The technical and graphical information contained in this handbook, to the best of our knowledge, was correct as it went to press. However, the Raytheon policy of continuous improvement and updating may change product specifications without prior notice. Therefore, unavoidable differences between the product and handbook may occur from time to time, for which liability cannot be accepted by Raytheon. [. . . ] on the menu bar to clear the form and start again. 34 Apelco GPS11 Installation and Operation Handbook Modifying a Waypoint Select MODIFY?on the menu bar and press the ENTER button. A list of stored waypoints will appear. wptlst01 Use the trackpad down arrow to highlight the required waypoint. Latitude, Longitude and comments will appear for each waypoint as the list is advanced. Press ENTER when the desired waypoint is located. wptcompl Use the trackpad to navigate around the screen and enter the modifications required. Highlight "VALID?" and press ENTER to store the changes or highlight "ERASE?" and press ENTER to clear the waypoint data and start again. Chapter 4: Operation 35 Deleting a Waypoint Select DELETE?on the menu bar and press the ENTER button. A list of stored waypoints will appear. wptlst01 Use the trackpad down arrow to highlight the required waypoint. Lat/ Lon and comments will appear for each waypoint as the list is advanced. Press ENTER when the desired waypoint is located. delwrn1 Press ENTER once more to confirm waypoint deletion or press PAGE to return to the main Waypoint information page. Note: If the waypoint is used in a route then an error message will appear giving the name of the route in which the waypoint is used. The route must be edited to remove the waypoint before the waypoint can be deleted from the waypoint list. 36 Apelco GPS11 Installation and Operation Handbook Activating a Waypoint To start the GPS11 tracking to a waypoint highlight "ACTI?" on the menu bar and press ENTER. actwpt01 You now have the option to select a waypoint from the stored list or to enter a new waypoint. Activating a Waypoint from the list Highlight "LIST?" on the menu bar and press ENTER. A list of stored waypoints will appear. wptlst01 Use the trackpad down arrow to highlight the required waypoint. Lat/ Lon and comments will appear for each waypoint as the list is advanced. Press ENTER when the desired waypoint is located. Chapter 4: Operation 37 Activating a new Waypoint Highlight NEW?on the menu bar and press the ENTER button. A blank waypoint data page will appear. editwp Follow the procedure on page 31 Entering a Waypoint to complete the form. Check the data entered carefully and, with the VALID?setting highlighted on the menu press ENTER to save the information. . Note: The new waypoint will be stored in memory and added to the waypoint list. If the information is incorrect you may use the trackpad arrows to go back and highlight the setting to be changed or highlight CLEAR?on the menu bar to clear the form and start again To stop tracking to a waypoint highlight "ACTI?" on the menu bar and press ENTER. [. . . ] 16 hrs in discontiouous mode with a use equivalent to one hour per day. Temperature Operating: Storage: -100 to +600C (140 to 1400F) -200C to +700C (-40 to 1580F) Data Output: Input: NMEA0182, and 0183. Waypoint loading and unloading with P. C. Plotter Functions Plotter Capacity: Plotter time scale: Plotter scales: 300 points 25 hours max. 0. 02 to 250 in the units selected Display of waypoints and active route plan. Chapter 6: Specification 55 Main Functions Chart Datums: Coordinates: Navigation: Waypoints: As shown in Appendix A of this manual. latitude, longitude, UTM, OSGB, Swedish Grid Speed and Course over the Ground. [. . . ]