User manual APPLIED ENERGY MW-EW 10

[. . . ] UK: Xpelair have a comprehensive range of services including: Free technical advice help-desk from Engineers on all aspects of ventilation. Free design service, quotations and site surveys. Service and maintenance contracts to suit all requirements. Please ask for details: By telephone on Techline: +44(0) 8709 000430 By fax on Techfax: +44(0) 8709 000530 At the address below International Guarantee - Contact your local distributor or Xpelair direct for details. [. . . ] Please ask for details: By telephone on Techline: +44(0) 8709 000430 By fax on Techfax: +44(0) 8709 000530 At the address below International Guarantee - Contact your local distributor or Xpelair direct for details. Technical advise and service - Contact your local Xpelair distributor. R R Applied Energy Products Ltd Morley Way Peterborough PE2 9JJ t 01733 456789 f 01733 310606 www. applied-energy. com Xpelair is a registered trademark of Applied Energy Products Limited. Applied Energy Products reserve the right to alter product specifications or appearance without prior notice. All finishes and diagrams in this booklet are as accurate as printing processes allow. Xplus multipoint ventilation unit Xplus 275 Leaflet Part No. 22750AA (Revision C) Xpelair Multipoint ventilation unit Installation and Operating Instructions PLEASE LEAVE THIS LEAFLET WITH THE FAN, FOR THE BENEFIT OF THE USER A Installing the ducting Where to locate it Position of air intake Installing the fan These products are intended for connection to fixed wiring. Check that the electrical rating shown on the products matches the mains supply. WARNING: THIS PRODUCT IS FOR CONNECTION TO 1 PHASE SUPPLY ONLY, DO NOT CONNECT TO 3 PHASE SUPPLY. WARNING: THIS APPLIANCE MUST BE EARTHED. All installations must be supervised by a qualified electrician. Installation and wiring must conform to current IEE regulations (UK), local or appropriate regulations (other countries). If installing in a position where condensation is likely to run back towards the fan, install a condensation trap as near to the fan as possible. Mounting the fan 1. Mount the fan, using appropriate fasteners through the mounting holes provided. Attach the ducting over the inlets and outlet and secure it with worm drive clips. Connecting the fan 1. Switch off the mains electrical supply and remove fuses. Connect the cable from the isolating switch to the electrical supply wiring. Refit fuse before turning on the electricity supply. Note: For fixed wiring circuits, the protective fuse for the appliance must not exceed 5A. Connecting the fan B N L MEDIUM SPEED GREEN/YELLOW BLUE BROWN FUSE N LOW SPEED DOUBLE POLE ISOLATING SWITCH HIGH SPEED L M H BLACK CABLE FITTED TO FAN Xplus 275 WIRING INSTRUCTIONS LINK WIRES. BLACK/WHITE 3 speed when used with an appropriate controller (not supplied). Suitable for continuous operation. The fan can be mounted to a suitably strong wall or roof member. Position of the air outlet 1. The fan can be operated using the controller (not supplied). The fan has 3 speed settings: High(H), Medium (M) and Low (L). Cleaning CONNECT TO OBTAIN REQUIRED SPEED Link to obtain speeds as follows L = Low Speed L - M = Medium Speed L - H = High Speed GREEN/YELLOW What the installer will need A means for disconnection in all poles must be incorporated in the fixed wiring in accordance with the wiring regulations. [. . . ] Suitable for continuous operation. The fan can be mounted to a suitably strong wall or roof member. Position of the air outlet 1. The fan can be operated using the controller (not supplied). The fan has 3 speed settings: High(H), Medium (M) and Low (L). Cleaning CONNECT TO OBTAIN REQUIRED SPEED Link to obtain speeds as follows L = Low Speed L - M = Medium Speed L - H = High Speed GREEN/YELLOW What the installer will need A means for disconnection in all poles must be incorporated in the fixed wiring in accordance with the wiring regulations. Ducting long enough to connect from the position of the air intake positions of the air outlet via the fan. [. . . ]