User manual ARCAM AVR500

[. . . ] AVR500/AVR600/AV888 AVRsurroundamplifier/AVprocessor Handbook POWER/STANDBY MENU INPUT + OK INFO MODE DIRECT DISPLAY ZONE MUTE VOLUME + AVR600 AUX PHONES VIDEO SCALING POWER English CAUTION ATTENTION RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR Class II product This equipment is a Class II or double insulated electrical appliance. It has been designed in such a way that it does not require a safety connection to electrical earth (`ground' in the U. S. ). safety guidelines RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: To reduce the risk of electric shock, do not remove cover (or back). Refer servicing to qualified service personnel. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. [. . . ] Help screen The lower right-hand panel gives a short help text for the feature being adjusted. navigating the setup menu . . . using the remote control The setup menu can be navigated by using the cursor (arrow) keys on the remote control. To enter the setup menu, press the MEnu button (which is located immediately under the navigation buttons). Use the B and C keys to navigate up and down the main section headings in the left-hand panel. Once you have the main section that you require highlighted, use the E key to enter the section. Use the B and C keys to navigate up and down the section settings in the left-hand panel. These are either for information only (e. g. incoming sampling frequency) or are not currently selectable (e. g. Scroll bars on the sides of the right hand panel indicate your position in the settings list where there are more items than can be displayed at once. Pressing oK selects a setting to change it, pressing oK again de-selects the setting. At any time, press the MEnu button to exit the menu. Any changes to settings are saved. . . . using the keys on the front panel The front panel controls can be used to configure the unit. Follow the instructions for using the remote control, in this case using inpuT for down, inpuT+ for up, inFo for left and MoDE for right. E-38 Entering Setup mode video &audio connection settings Before entering the menu, select the input that you wish to change (e. g. To enter the setup menu, press the AMp button followed by the MEnu button on the remote control. The front panel display shows `MENU' and the setup menu (pictured right) is displayed. Press the remote control E key to enter the Input Config menu then use the Ckey to navigate down to the Video Source option. Input Config General Setup Auto Setup Spkr Types Spkr Distance Spkr Levels Video Inputs Video Outputs Mode Zone Settings Network Colour Picture Mode Edge Enhancement Mosquito NR Noise Reduction Block NR Component Mode Video Source Audio Source HDMI > Component S-Video Composite Selecting the video source Once the Video Source option is highlighted as shown, press the oK key to select it for modification. Use the B and C keys to select from the list the video type you are using on this source. < HDMI: the unit is forced to use the HDMI video input for this source. < Component: the unit is forced to use the Component/RGB video input for this source. < S-Video: the unit is forced to use the S-Video input for this source. < Composite: the unit is forced to use the Composite video input for this source. Each input on the AVR500/AVR600/AV888 has multiple connection possibilities for both audio and video, including HDMI, Component Video, digital audio and analogue audio. [. . . ] < sometimes Dolby Digital DVD discs contain material at either the beginning or the end of the main movie that is not in full 5. 1 format, but in twochannel or Pro Logic decoding. If you cannot connect to a wired network < the Ethernet cable you are using is correctly connected between the < the network is set up for fixed IP addressing and you have the AVR500/ < the network is set up for DHCP and you have the AVR500/AVR600/AV888 < all cables are making a good connection. If necessary withdraw the cable from the connector and plug it fully in again (turn the power off before doing this). < the connections inside the source cable connector are not broken or badly soldered. < if the hum originates only when one particular source component is connected, that an aerial cable, or dish connection to this source is ground isolated. [. . . ]