User manual ARISTO AM-235

[. . . ] 1 Electronic Emission Notices Federal Communications Commission (FCC) Statement (41532C) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with instructions contained in this manual, may cause harmful interference to radio and television communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] When the DIMM is seated, push down on the top edge of the DIMM until the retaining clips at the ends of the socket snap into place. Make sure the clips are firmly in place. Turn system power off before installing and removing any device, otherwise you'll cause the system damage. Technical Reference Booklet 9 Installing a New Processor An upgrade processor can dramatically increase general system speed and performance. Most microprocessor upgrade kits include the following items: Microprocessor chip Installation instructions and technical data Before installing the processor, please refer to the installation notes that available with the CPU package. To Install a Processor to ZIF Socket To install the processor, follow these steps: 1. If the system microprocessor is already on the motherboard socket, you need to remove it from the motherboard socket. The socket is a Zero Insertion Force (ZIF) socket which has a metal arm at one side. Carefully grasp this arm, move it horizontally away from the socket and lift it up. You may also restart by simultaneously pressing the <Ctrl>, <Alt>, and <Delete> keys. If you do not press the keys at the correct time and the system does not reset, an error message will be displayed and you will again be asked to . . . PRESS F1 TO CONTINUE, DEL TO ENTER SETUP Getting Help Press F1 to pop up a small help window that describes the appropriate keys to use and the possible selections for the highlighted item. To exit the Help Window press <Esc> or the F1 key again. In Case of Problems If, after making and saving system changes with the Setup Program, you discover that your computer does not reset, use the Award BIOS defaults to override the CMOS settings. Technical Reference Booklet 11 Main Menu Once you enter the Award BIOS CMOS Setup Utility, the Main Menu will appear on the screen. The Main Menu allows you to select from various setup functions and two exit choices. Use the arrow keys to select among the items and press <Enter> to accept and enter the sub-menu. CMOS Setup Utility - Copyright (C) 1984-2001 Award Software Standard CMOS Features Advanced BIOS Features Advanced Chipset Features Integrated Peripherals Power Management Setup PnP/PCI Configurations PC Health Status Esc : Quit F10 : Save & Exit Setup Frequency/Voltage Control Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Set User Password Save & Exit Setup Exit Without Saving : Select Item Time, Date, Hard Disk Type . . . (Note : The figures of BIOS Setup Menu included here only show a typical case, and may not be exactly the same as the one on your unit. ) Note that a brief description of each highlighted item will appear at the bottom of the screen. Standard This setup page includes all the items of AwardTM special standard CMOS Features features. Advanced BIOS Features This setup page includes all the items of AwardTM special enhanced features. Advanced This setup page includes all the items of chipset special features. Chipset Features Integrated Peripherals Power Management Setup PNP/PCI Configurations This section page includes all the items of IDE hard drive and Programmed Input / Output features. This entry only appears if your system supports Power Management "Green PC" standards. This entry appears if your system supports PNP/PCI. PC Health Status Display CPU and Case Fan Speed. Frequency/ CPU speed setting are settings of CPU speed. You should refer to Voltage Control your CPU marking. BIOS Setup 12 Load Fail-Safe Defaults The BIOS defaults have been set by the manufacturer and represent settings which provide the minimum requirements for your system to operate. The chipset defaults are settings which provide for maximum system performance. While Award has designed the custom BIOS to maximize performance, the manufacturer has the right to change these defaults to meet its needs. It allows you to limit access to the system and the Setup Program. [. . . ] - Click right button of the mouse, then select PROPERTIES. - Select the DRIVER item and UPDATE DRIVER. - The UPDATE DEVICE DRIVER WIZARD will appear. - Click DISPLAY A LIST OF THE KNOW DEVICE, then click NEXT. [. . . ]