User manual ARISTO AM-535P

[. . . ] 1 Electronic Emission Notices Federal Communications Commission (FCC) Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with instructions contained in this manual, may cause harmful interference to radio and television communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] - JP8 set "1-2" means Synchronous CPU Clock/PCI Clock. JP8 set "2-3" means ASynchronous CPU Clock/PCI Clock (always 32MHz). - * = Default setting. Technical Reference Booklet 7 JP14 JP13 JP12 JP16 JP11, J12, J13, J14, JP16 - Power Selection for the CPU Core Voltage, Bus Section and Bus Voltage CoreVoltage JP11 1 1 1 1 1 BUS Section BUSVoltage JP12, JP13, 14 JP16 1-2 1-2 1-2 1-2 1-2 2-3 (3. 3V) 2-3 (3. 3V) 2-3 (3. 3V) 2-3 (3. 3V) 1-2* (3. 5V) CPU Examples for further CPUs AMD® K6 (266Mhz or above) AMD K5 ("K" marking) AMD K5 ("J" marking) Intel® Pentium Processors with MMX Technology 1 JP11 (1. 8V) (2. 1V) (2. 5V) (2. 7V) (2. 8V) (2. 8V) 1-2 2-3 (3. 3V) Cyrix 6x86L (Core 2. 8V I/O 3. 3V) 1 (2. 9V) 1-2 2-3 (3. 3V) IBM®, Cyrix® 6x86MX, AMD K5 ("H" marking) 1 1 1 1 1 1 (2. 9V) (2. 9V) (3. 2V) (3. 3V) (3. 5V) (3. 5V) 1-2 1-2 1-2 2-3* 2-3* 2-3* 1-2* (3. 5V) 1-2* (3. 5V) 1-2* (3. 5V) 1-2* (3. 5V) 1-2* (3. 5V) 1-2* (3. 5V) AMD K6 PR2-166 AMD K6 PR2-200 AMD K6 PR2-233 AMD K5 ("B", "C"or"F" marking) Intel P54C Cyrix 6x86 Remark: Example of AMD marking : "AMD-K5-PR100ABQ" In the above tables, the AMD marking refers to the 2nd character - (B in the example) after P-rating (PR100 in the example). · Note that a DRAM module has a polarity notch at one end so that it fits into a socket only one way. Align the DRAM module edge connector with the slot at the center of the socket. Position the DRAM module to the left of the socket and press the DRAM module edge connector firmly into the socket. · · If you have misaligned or only partially seated the module, remove the DRAM module gently and reinstall it. Installing the Processor For easy installation of the CPU, it is recommended that you remove all Cards in PCI solts first. · · · Unpack the CPU and identify the pin 1 corner of the CPU. Match pin 1 of the CPU with pin 1 of the CPU socket. The pin 1 corner of the CPU socket is designated by a small triangle printed on the motherboard. Carefully insert the CPU into the CPU socket and move the metal arm downward to replace it in its original position. Change any jumper settings as detailed in the manual. The small circle marked on the top of the CPU designates the pin 1 corner. If a heat sink is attached and covers the top of the CPU, identify the pin 1 corner by turning the CPU over. Locate the small gold finger that extends from one corner of the large central square portion of the CPU. The gold finger points towards pin 1, which is also uniquely identified by a square pad. Positioning the CPU incorrectly in the socket can permanently damage the CPU and the computer when you turn on the system. Technical Reference Booklet 11 BIOS SETUP This chapter discusses Award's Setup Program built into the ROM BIOS. The Setup Program allows users to modify the basic system configuration. This special information is then stored in battery-backed RAM, which retains the setup information when the power is turned off. Starting Setup The Award BIOS is immediately activated when you turn on the computer. The BIOS reads the system information contained in the CMOS and begins the process of checking out the system and configuring it. When it finishes, the BIOS will seek an operating system on one of the disks and then launch and turn control over to the operating system . While the BIOS is in control, the Setup Program can be activated : 1. By pressing <Del> immediately after switching the system on, or 2. By pressing the <Del> key when the following message appears briefly at the bottom of the screen during the POST (Power On Self Test ) Press DEL to enter SETUP If the message disappears before you can respond and you still wish to enter Setup, restart the system to try again by turning it OFF then ON or pressing the "RESET" button on the system case. [. . . ] The new password will clear the previously entered password from the CMOS memory . You will be asked to confirm the password. Type the password again and press <Enter>. You may also press <Esc> to abort the selection and operate without a password. [. . . ]