User manual ARISTO AM-597

[. . . ] 1 Electronic Emission Notices Federal Communications Commission (FCC) Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with instructions contained in this manual, may cause harmful interference to radio and television communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] - This motherboard is compatible with Cyrix 6x86 CPU, which must be Revision 2. 7 or newer. Please contact your CPU supplier for details on identification of Cyrix 6x86 CPU revisions - This motherboard can be run with Cyrix 6x86-P200+ CPU specifications of all add on cards. If system does not behave reliably at 75MHz Bus Clock , you should set the Bus Clock to 50MHz (JP3 set "2-3", JP4 set "2-3", JP5 set "2-3"). - JP8 set "1-2" means Synchronous CPU Clock/PCI Clock. JP8 set "2-3" means ASynchronous CPU Clock/PCI Clock (always 32MHz). - * = Default setting. WARNING - The VIA® VP3 Chipset are not validated to run at CPU CLK of 75MHz or higher. Therefore, the reliability at these speeds are not guaranteed. Some PCI/AGP cards may not run reliably at over CPU CLK speeds higher than 66MHz. Technical Reference Booklet 7 JP16 JP13 JP12 JP11, JP12, JP13, JP16 - Power Selection for the CPU Core Voltage, Bus Section and Bus Voltage CoreVoltage JP11 1 1 1 1 1 BUS Section JP12, JP13 1-2 1-2 1-2 1-2 1-2 BUSVoltage JP16 CPU Examples for further CPUs AMD® K6 (266Mhz or above) AMD K5 ("K" marking) AMD K5 ("J" marking) Intel® Pentium Processors with MMX Technology 1 JP6 JP2 JP1 (1. 8V) (2. 2V) (2. 5V) (2. 7V) (2. 8V) (3. 3V) (3. 3V) (3. 3V) (3. 3V) (3. 5V) (2. 8V) 1-2 JP11 JP8 JP5 JP4 JP3 (3. 3V) IBM®/Cyrix® 6x86L (Core 2. 8V I/O 3. 3V) 1 (2. 9V) 1-2 (3. 3V) IBM/Cyrix 6x86MX, AMD K5 ("H" marking) 1 1 1 1 1 1 (2. 9V) (2. 9V) (3. 2V) (3. 3V) (3. 5V) (3. 5V) 1-2 1-2 1-2 2-3* 2-3* 2-3* (3. 5V) (3. 5V) (3. 5V) (3. 5V) (3. 5V) (3. 5V) AMD K6 PR2-166 AMD K6 PR2-200 AMD K6 PR2-233 AMD K5 ("B", "C"or"F" marking) Intel P54C IBM/Cyrix 6x86 Remark: Example of AMD marking : "AMD-K5-PR100ABQ" In the above tables, the AMD marking refers to the 2nd character - (B in the example) after P-rating (PR100 in the example). · Note that a DRAM module has a polarity notch at one end so that it fits into a socket only one way. Align the DRAM module edge connector with the slot at the center of the socket. Position the DRAM module to the left of the socket and press the DRAM module edge connector firmly into the socket. · · If you have misaligned or only partially seated the module, remove the DRAM module gently and reinstall it. Installing the Processor For easy installation of the CPU, it is recommended that you remove all Cards in PCI slots first. · · · Unpack the CPU and identify the pin 1 corner of the CPU. Match pin 1 of the CPU with pin 1 of the CPU socket. The pin 1 corner of the CPU socket is designated by a small triangle printed on the motherboard. Carefully insert the CPU into the CPU socket and move the metal arm downward to replace it in its original position. Change any jumper settings as detailed in the manual. The small circle marked on the top of the CPU designates the pin 1 corner. If a heat sink is attached and covers the top of the CPU, identify the pin 1 corner by turning the CPU over. Locate the small gold finger that extends from one corner of the large central square portion of the CPU. The gold finger points towards pin 1, which is also uniquely identified by a square pad. Positioning the CPU incorrectly in the socket can permanently damage the CPU and the computer when you turn on the system. Technical Reference Booklet 11 BIOS SETUP This chapter discusses Setup Program built into the ROM BIOS. The Setup Program allows users to modify the basic system configuration. This special information is then stored in battery-backed RAM, which retains the setup information when the power is turned off. Starting Setup The BIOS is immediately activated when you turn on the computer. [. . . ] User Password : You can enter the Setup Program but only change the User Password. When you select this function, the following message will appear at the center of the screen to assist you in creating a password. ENTER PASSWORD: Type the password, up to six characters in length, and press<Enter>. The new password will clear the previously entered password from the CMOS memory. You will be asked to confirm the password. [. . . ]