User manual ARISTO AM-619

[. . . ] 1 Electronic Emission Notices Federal Communications Commission (FCC) Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with instructions contained in this manual, may cause harmful interference to radio and television communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] Refer to this chapter whenever in doubt. JP40 1 JP39 1 JP38 1 1 1 1 1 1 1 1 JP26 JP37 JP1 JP2 JP3 JP4 JP31 JP1, JP2, JP3, JP4, JP6, JP8 - CPU Type Selection CPU Type and Speed Pentium II - 233MHz* Pentium II - 266MHz Pentium II - 300MHz Pentium II - 333MHz Pentium II - 350MHz Pentium II - 400MHz Pentium II - 450MHz 1 JP6 JP8 1 1 JP1 (1-2*) (1-2) (1-2) (1-2) (1-2) (1-2) (1-2) 1 JP2 (1-2*) (2-3) (2-3) (2-3) (1-2) (2-3) (2-3) 1 JP3 (2-3*) 1 (1-2) (2-3) (1-2) (2-3) (1-2) (2-3) 1 JP4 (2-3*) (1-2) (1-2) (2-3) (2-3) (1-2) (1-2) 1 JP6 (1-2*) 1 (1-2) (1-2) (1-2) (2-3) (2-3) (2-3) 1 JP8 (1-2*) (1-2) (1-2) (1-2) (2-3) (2-3) (2-3) 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 If the CPU type is 100XMHz(eg. 350MHz, 400MHz, 450MHz), the DIMM must be PC-100. JP31 - CMOS Clear JP31 1 Selection (2-3*) (1-2) Normal* CMOS Clear 1 * =Default setting Close Open Technical Reference Booklet 7 JP26, JP37 - BIOS Program Voltage JP26 1 1 1 1 JP37 (1-2) (2-3) (2-3) (2-4) 1 1 1 1 Selection (1-2) (1-2) (2-3) (2-3) INTEL MX ATMEL/SST 2M BIOS JP26 & JP37 are pre-installed in the factory. They should NOT be altered by the users. JP38, JP39, JP40 - Sound Enable JP38 1 1 JP39 (1-2*) (2-3) 1 1 JP40 (1-2*) (2-3) 1 1 Selection (1-2*) (2-3) Enable Sound* Disable Sound * =Default setting Close Open Hardware Setup 8 Installation Installing the Retention Mechanism for Intel® Pentium® II or Intel® Celeron® Processor To install the retention mechanism, follow these steps: 1. Locate Slot 1 and the four attachment holes on the motherboard. To position the mechanism, orient it as shown in figure. The tab on the connector fits into a notch in the base of the mechanism. Press down on the studs until it is firmly seated in attachment holes. When properly seated, the base of the mechanism is flush with the motherboard. Studs Adapter for Intel® Celeron® CPU (This adapter is for installing the Celeron® CPU only) Attachment Holes Retention Mechanism Slot 1 Installing the Processor To install the processor, follow these steps: 1. Insert the processor in the retention mechanism. Press down on the processor until it is firmly seated in the Slot 1 connector. Intel® Pentium II® CPU Latches Intel® Celeron® CPU Retention Mechanism Retention Mechanism Technical Reference Booklet 9 Installing the DIMMs 1. Turn off all peripheral devices connected to the computer. Remove the computer cover and locate the DIMM sockets. Holding the DIMM by the edges, remove it from its antistatic package. Make sure the clips at either end of the socket are pushed away from the socket. Clip DIMM Clip DIMM Socket Notch 5. Align the two small notches in the bottom edge of the DIMM with the keys in the socket. Insert the bottom edge of the DIMM into the socket. When the DIMM is seated, push down on the top edge of the DIMM until the retaining clips at the ends of the socket snap into place. Make sure the clips are firmly in place. If you installed a DIMM with ECC memory, start the computer and use the ECC Configuration feature in Setup to enable the use of ECC. Setting the Processor Speed After you install the processor and install the motherboard, set the processor speed by CMOS setup. Change the CPU speed as detailed in the manual. Hardware Setup 10 BIOS SETUP This chapter discusses Awards Setup Program built into the ROM BIOS. The Setup Program allows users to modify the basic system configuration. [. . . ] This section covers some very technical items and it is recommended that only experienced users should make any changes to the default settings. Integrated Peripherals The Integrated Peripherals Setup allows the user to configure the onboard IDE controller, floppy disk controller, the printer port and the serial ports. Supervisor/User Password Setting Supervisor Password : User Password : You can set either supervisor or user password, or both of them. The difference between them are: You can enter the Setup Program and change the options of the setup menus. You can enter the Setup Program but cannot change the options of the setup menus. When you select this function, the following message will appear at the center of the screen to assist you in creating a password. Technical Reference Booklet 15 ENTER PASSWORD: Type the password, up to eight characters in length, and press<Enter>. The new password will clear the previously entered password from the CMOS memory. [. . . ]